Güde 85014 Mode D'emploi Original page 7

We strive to continually improve our products. Therefore, to
change specifications and pictures!
Unit
Electrical Heater 15 kW 400 V
A sturdy electrical heater Güde with a fan fitted.
Area of Use:
Electrical heaters are typically used in construction, ship
building, agriculture, car repair workshops, cooking, asseblies
and anywhere where oil and gas heaters are not permitted. .
Electrical Heater 15 kW 400 V
A sturdy electrical heater Güde with a fan fitted.
Area of Use:
Electrical heaters are typically used in construction, ship
building, agriculture, car repair workshops, cooking,
assemblies and anywhere where oil and gas heaters are not
permitted.
Voltage:
Maximum heating capacity:
Heating degrees
Weight:
Ordering No.:
Description Pic. A
1. Carrying handle and a foot
2. Protection grid
3. Capacity degrees switch
4. Thermostat controller
5. Reset hole
Scope of Delivery
Electrical heater with a carrying handle enabling mobile use
Warranty
Warranty claims in accordance to the warranty certificate
attached.
General Safety Instructions
Prior to the initial use of the unit, the operating instructions
should be read completely. If in doubt with regard to
connection and operation of the unit, consult the manufacturer
(servicing department).
FOLLOW THE INSTRUCTIONS BELOW CAREFULLY IN
ORDER TO SECURE A HIGH DEGREE OF SAFETY:
Always observe local construction and fire
prevention regulations and the professional
associations regulations when using the unit.
Material, function and quality has been extensively checked
on before delivery. Nonetheless, the units may cause danger
if used unprofessionally or by untrained persons contrary to
the determination !
Caution!
Check the unit for damages before every use .
Observe the value of the mains voltage (400 V ~ 50 Hz).
Please mind that hazards may arise when electrical
instruments are used unprofessionally .
Keep children away from electrical heaters. .
400 V/50 Hz/CEE 32 A
15 kW
5 kW/10 kW/15 kW + Fan
14,5 kg
85014
Have any defective or damaged parts promptly replaced
by a professional.
Protect the unit from rain, water splashes and moisture.
The authorised operators should check the units for any
visible defects of control and safety devices and for the
protection devices proper function .
The supervision manager should be advised
immediately any time when defects are found out.
On finding defects that threaten the units safety, the
operation of the units has to be interrupted immediately.
Existing local regulations and respective electrical
protections have to be observed when using the units.
Mind the safety distance from flammable objects.
Unobstructed air suction and output have to be
guaranteed at any time.
The air outlet should not be narrowed or equipped with
tubes and hoses.
Never put foreign objects in the units.
Never cover up the units in operation.
The safety devices should not be bridged over or
blocked .
The units should not be operated directly below the wall-
mounted socket.
The units should not be exposed to a direct stream of
water, such as from a high-pressure cleaner.
Water should never intrude in the units.
Units should not be installed and operated in the
environment of the fire and explosion hazards..
Units should never be installed and operated in an
atmosphere with oil, sulphur and salt content
Protect all the electrical cables of the units from damage,
fro damage by animals as well.
The units are heating automatic instrument for industrial
use varying from site to site. .
The units awe electrically operated only and are
designed to be used automatically, universally and free
of any faults.
The units are fitted with especially encased heating
resistors, decreased noise featuring axial fans requiring
minimum maintenance, protection thermostats and after-
cooling thermostats, room thermostat socket and an
electrical cable with protection contact.
The units comply with fundamental requirements of
safety and health safety given by respective EU
provisions.
The operation of the units is safe and easy.
Among other, the units may be used for :
Drying newly constructed buildings.
Spotted heating of outdoor work areas or in halls and
factory spaces not endangered by fire.
Temporary or permanent heating of rooms.
7