Machine Start And Stop; Stopping The Machine - Nilfisk ECOFLEX Adfinity 17ST Instructions D'utilisation

ENGLISH
Squeegee installation
1. Install the squeegee (25) and fasten it with the handwheels (26), then connect the vacuum hose (15) to the squeegee.
2. With the handwheel (27), adjust the squeegee so that the rear blade - in all its length - touches the fl oor and the front blade is
slightly detached from the fl oor.
Solution or washing water tank fi lling
1. (For Adfi nity™ 17ST - 20ST)
Use the fi ller neck (37) to fi ll the tank (20) with a solution suitable for the work to be carried out.
Do not fi ll the solution tank completely, leave few inches from the edge.
Always follow the dilution instructions on the label of the chemical product used to create the solution.
The solution temperature must not exceed +104°F (+40°C).
CAUTION!
Use only low-foam and non-fl ammable detergents, intended for automatic scrubber applications.
(For Adfi nity™ X20R)
Use the fi ller neck (37) to fi ll the tank (20) with clean water.
Do not fi ll the clean water tank completely, leave a few inches from the edge.
The water temperature must not exceed +104°F (+40°C).
Detergent tank fi lling (for Adfi nity™ X20R)
1. Open the cover (22) and check that the recovery water tank (21) is empty, otherwise empty it with the drain hose (16).
2. Grasp the handle (41) and carefully lift the tank (40).
3. Open the plug (46).
4. Fill the tank (45) with a detergent suitable for the work to be carried out (highly concentrated detergents).
Do not fi ll the detergent tank completely, leave a few inches from the edge.
CAUTION!
Use only low-foam and non-fl ammable detergents, intended for automatic scrubber applications.
NOTE
If the detergent hose (48) is empty (in case of new system, system emptied for cleaning, etc.), in order to fi ll the hose
quickly, it may be useful to drain the EcoFlex™ once or several times (see the procedure in the Maintenance chapter).

MACHINE START AND STOP

Starting the machine
1. Prepare the machine as shown in the previous paragraph.
2. (Only for Adfi nity™ X20R): Insert the ignition key (80) and turn it to "I".
(Only for Adfi nity™ 17ST - 20ST): Press the switch (71) or (73) to turn the machine on.
Check that the green warning led (81a) turns on (charged batteries).
If the yellow or red warning led (81b) or (81c) turns on, turn off the machine by pressing the switch (71) and/or (73), then
charge the batteries (see the procedure in the Maintenance chapter).
3. Drive the machine to the working place:
• By pushing it with the hands on the handlebar (2) (only for Adfi nity™ 17ST - 20ST).
• By starting it with the hands on the handlebar (2) and pushing the paddle (3) forward to move forward, and backwards to
move in reverse (only for Adfi nity™ X20R).
The maximum forward speed can be adjusted with the adjuster (4).
4. Lower the squeegee (25) with the lever (10).
5. Lower the brush/pad-holder deck by pressing the pedal (11).
6. Press the brush/pad-holder and vacuum system switch (71).
7. Press the washing water fl ow control switches (82) as necessary, depending on the type of cleaning to be carried out.
8. Start cleaning, by moving the machines as shown in step 3. If necessary, adjust the maximum speed with the adjuster (4).

Stopping the machine

9. Stop the machine with the handlebar (2) (only for Adfi nity™ 17ST - 20ST).
Stop the machine by releasing the paddle (3) (only for Adfi nity™ X20R).
10. Turn off the brushes/pad-holders and the vacuum system by pressing the switches (71) and (73).
11. Lift the brush/pad-holder deck by pressing the pedal (11).
12. Lift the squeegee (25) with the lever (10).
13. Make sure that the machine cannot move independently.
14
INSTRUCTION FOR USE
9096912000(4)2010-11 Adfi nity™ 17ST - 20ST - X20R