Publicité
Technical Data
Hedge trimmer .............................................. GTHS 565
Art. No ......................................................................................... 93995
Service connection ...................................230 V~50 Hz
Motor output ..................................................... 550 W/P1
knife movement ............................................ 1600 min
knife Spacing ...........................................................16 mm
Cutting length ......................................................460 mm
Beam length ........................................................565 mm
Weight ..........................................................................4,5 kg
Degree of protection .............................................. IP 20
Protection class ...................................................................II
Noise and Vibration Information
Sound pressure level L
.........................................82 dB (A)
1)
PA
Measured sound power level L
Guaranteed sound power level L
Wear ear protectors!
Schwingungsemissonswert Vorderer Griff a
Schwingungsemissonswert Hinterer Griff a
1)
Uncertainty K= 3 dB (A),
2)
Uncertainty K= 1,5 m/s
Warning: The vibration emission level will vary because
of the ways in which a power tool can be used and may
increase above the level given in this information sheet.
The vibration emission level may be used to compare
one tool with another.
It may be used for a preliminary assessment of exposure.
An accurate estimate of the vibratory load should also
take into account the times when the tool is shut down
or when it is running but not actually in use. This may
significantly reduce the vibratory load over the total
working period.
Identify additional safety measures to protect the ope-
rator from the effects of vibration such as maintain
the tool and the accessories, keep the hands warm,
organisation of work patterns.
Read and understand the operating
instructions before using the appliance. Abide by all
the safety measures stated in the service manual. Act
responsibly toward third parties.
In case of any doubts about connection and
operation refer please to our customer center
Power tool description
1.
Safety switch
2.
Front hands protection
3.
Knife/cutter bar
-1
(A)
1
....................... 93 dB
)
WA
..........................96 dB (A)
WA
............3,0 m/s
2)
2
h
2)
............3,0 m/s
2
h
2
4.
Screw telescopic adjustment
5.
Knife/cutter bar protection
6.
cable strain relief
7.
Power supply cable
8.
ON/OFF switch
Specified Conditions Of Use
The hedge trimmer is designed for trimming shrubs
and hedges in private hobby gardens
The device must not be used for crushing compost,
as persons or damage to property können.The hedge
trimmer is designed for trimming shrubs and hedges
in private hobby gardens.
Do not use this product in any other way as stated
for normal use. Not observing general regulations
in force and instructions from this manual does not
make the manufacturer liable for damages.
The charger may only be operated with a
protective switch against stray current (RCD
max. stray current 30mA).
Requirements for operating staff
The operating staff must carefully read the Opera-
ting Instructions before using the appliance.
Qualification : Apart from the detailed instructions
by a professional, no special qualification is necessary
for appliance using.
Minimum age : Persons over 18 years of age can
only work on the appliance. An exception includes
youngsters trained in order to reach knowledge
under supervision of the trainer during occupational
education.
Training : Using the appliance only requires corre-
sponding training by a professional or the Operating
Instructions. No special training is necessary.
The operator is responsible for accidents or risks to
third parties.
Observe to keep out of dangerous zone
Emergency procedure
Conduct a first-aid procedure adequate to the injury
and summon qualified medical attendance as quickly
as possible. Protect the injured person from further
harm and calm them down. For the sake of eventual
accident, in accordance with DIN 13164, a workplace
has to be fitted with a first-aid kit. It is essential to
replace any used material in the first-aid kit immedia-
tely after it has been used.
If you seek help, state the following pieces of infor-
mation
ENGLISH
17
Publicité
