Güde GSB 20 Traduction Du Mode D'emploi D'origine page 28

ENGLISH
24
Check the connection cable on the electric tool at
regular intervals and have it replaced by an expert
if it is damaged.
Check the extension cables at regular intervals and
replace them if they are damaged.
Keep the handles dry, clean and free of oil and
grease.
Pull the plug out of the socket and/or remove the
battery when the tool is not in use before you
make machine settings or change accessories,
such as the saw blade, drill bit or cutter. This safety
measure prevents unintentional starting of the
electric tool.
Before starting any electric tool, remove any
adjusting wrenches and screwdrivers. A tool or a
wrench present in the rotating part of the machine
may lead to injuries.
Prevent the machine from unintentional starting.
Before plugging and/or connecting the machine
to battery, handling or carrying, make sure the
electric tools are switched off. Having a finger on
the switch when carrying the electric tool or when the
machine is on when plugging it may lead to injuries.
If you wish to work outdoors with an electric tool,
only use extension cables which are approved for
outdoor use and are marked accordingly. Using an
extension cable suitable for outdoor use reduces the
risk of electric shock.
Be careful, pay attention to what you are doing
and use common sense when working with
electric tools. Do not use electric tools when you
are tired or under the influence of drugs, alcohol
or pharmaceuticals. A moment if inattention when
using electric tools may lead to serious injuries.
Check the machine for any damage. Before using
the equipment again, the protective equipment
must carefully be checked if safe and working as
designated.
Check the moving parts for perfect functioning, if
working smoothly and if no parts are damaged. To
provide safe operation of the equipment, all parts
must be installed properly and meet all conditions.
Damaged protective equipment and parts must be
professionally repaired or replaced by a recognised
professional workshop, unless otherwise specified
in the Operating Instructions.
Do not use electric tools with a defective switch.
An electric tool that cannot be switched on or off is
dangerous and must be repaired.
Have your electric tool repaired by an electrician.
This electric tools complies with the relevant safety
regulations. Repairs may only be carried out by an
electrician using genuine spare parts; otherwise the
user may suffer accidents.
Caution!
The machine must be secured to the floor using
suitable screws since otherwise there is a risk that it
will tip over.
Inspect before each use.
• Proper function of the on and off button, incl. the
emergency switch.
• Carry out a visual inspection before switching the
appliance on.
• Check especially the safety equipment, electrical
control elements, power lines and screw couplings
for any damage and if they are tightened approp-
riately. If necessary, replace damaged parts before
operation.
• Ensure that the bench clamping lever is tightly
secured before starting up the machine.
• Ensure that the drill is safely secured in the clam-
ping chuck.
• REMOVE ADJUSTING KEYS AND WRENCHES. From
habit of checking to see that keys and adjusting
wrenches are removed from tool before turning
it "ON".
Risk of injury!
Keep body parts and clothes away from rotating
parts of the device.
Use protective equipment which fit you.
Wear a hairnet if you have long hair.
Do not wear gloves when operating a drill.
Do not attempt to drill into a material that does not
have a flat surface, unless you are using a suitable
support.
Never start the drilling machine with the drill pressed
against the workpiece.
Always use clamps, chuck jaws or a vice to secure the
workpiece to the bench.
Set the drilling machine to a speed that is appropriate
for the specific job.
In the event of a blockage, switch off the machine
immediately. Pull out the mains plug and remove the
jammed workpiece.
Chips and splinters must not be removed while the
machine is running.
Mains Connection
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Connect only to a single-phase AC current supply
and only to the mains voltage specified on the rating
plate. Must only be used from sockets with earth
wire.