Télécharger Imprimer la page

Güde WS 125-900 Traduction Du Mode D'emploi D'origine page 19

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 22
Speci ed Conditions Of Use
The angle grinder is used for grinding and cutting
metal, stone and ceramic materials, as well as for
sanding.
Use the cutting guard from the accessories range for
cutting application.
Please refer to the instructions supplied by the acces-
sory manufacturer.
The machine is suitable only for working without water.
Do not use this product in any other way as stated for
normal use. Not observing general regulations in force
and instructions from this manual does not make the
manufacturer liable for damages.
Emergency procedure
Conduct a rst-aid procedure adequate to the injury and
summon quali ed medical attendance as quickly as pos-
sible. Protect the injured person from further harm and
calm them down. If you seek help, state the following
pieces of information: 1. Accident site, 2. Accident type,
3. Number of injured persons, 4. Injury type(s)
Symbols
WARNING / Caution!
Read the operating instructions to reduce
the risk of injury.
Wear eye protective goggles !
Wear ear protectors!
Wear a suitable dust protection mask.
Wear gloves!
Unplug the machine before any work
on it.
Keep bystanders a safe distance away
from work area. Anyone entering the
work area must wear personal protective
equipment.
Class II tool.
CE marking
Any damaged or disposed electric or
electronic devices must be delivered to
appropriate collection centres.
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or
serious injury.
Save all warnings and instructions for future
reference.
Angle Grinder Safety Warnings
Safety Warnings Common for Grinding, Sanding or
Abrasive Cutting-O Operations:
a) This power tool is intended to function as a
grinder, sander or cut-o tool. Read all safety
warnings, instructions, illustrations and speci-
cations provided with this power tool. Failure
to follow all instructions listed below may result in
electric shock, re and/or serious injury.
b) Operations such as wire brushing and poli-
shing are not recommended to be performed
with this power tool. Operations for which the pow-
er tool was not designed may create a hazard and
cause personal injury.
c) Do not use accessories which are not speci-
cally designed and recommended by the tool
manufacturer. Just because the accessory can be
attached to your power tool, it does not assure safe
operation.
d) The rated speed of the accessory must be at
least equal to the maximum speed marked on the
power tool. Accessories running faster than their
rated speed can break and y apart.
e) The outside diameter and the thickness of
your accessory must be within the capacity rating
of your power tool. Incorrectly sized accessories
cannot be adequately guarded or controlled.
f) Treaded mounting of accessories must match
the grinder spindle thread. For accessories
mounted by anges, the arbour hole of the
accessory must t the locating diameter of the
ange. Accessories that do not match the mounting
hardware of the power tool will run out of balance,
vibrate excessively and may cause loss of control.
g) Do not use a damaged accessory. Before each
use inspect the accessory such as abrasive wheels
for chips and cracks, backing pad for cracks, tear
or excess wear, wire brush for loose or cracked wi-
res. If power tool or accessory is dropped, inspect
for damage or install an undamaged accessory.
After inspecting and installing an accessory,
position yourself and bystanders away from the
plane of the rotating accessory and run the power
tool at maximum noload speed for one minute.
Damaged accessories will normally break apart during
this test time.
h) Wear personal protective equipment. De-
pending on application, use face shield, safety
goggles or safety glasses. As appropriate, wear
dust mask, hearing protectors, gloves and shop
apron capable of stopping small abrasive or
workpiece fragments. The eye protection must
ENGLISH
15

Publicité

loading

Ce manuel est également adapté pour:

Ws 125-1150 e5810758108