Certifications
This product meets the Essential Requirements of all relevant
European directives and is eligible for CE marking.
Meets essential requirements of the following European Directives:
• Low Voltage Directive 2006/95/EC
• R&TTE Directive 99/5/EC
• WEEE Directive 2002/96/EC, as amended by 2008/34/EC
• RoHS Directive 2002/95/EC, as amended by 2008/35/EC
Note: Please follow your regional recycling scheme for batteries and
electronic waste
Conforms to the relevant requirements of regulation (EC)
No.278/2009, for low voltage external power supplies.
Meets requirements of the following standards:
EN 300 422 Parts 1 and 2. EN 301 489 Parts 1 and 9.
The CE Declaration of Conformity can be obtained from: www.shure.
com/europe/compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Fax: 49-7262-92 49 11 4
Email: EMEAsupport@shure.de
P3RA
Approved under the Declaration of Conformity (DoC) provision of FCC
Part 15.
Complies with requirements set out in RSS-GEN.
This Class B digital apparatus complies with Canadian ICES-003. Cet
appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation of this device is subject to the following two
conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas
produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
Important Product Information
LICENSING INFORMATION
Licensing: A ministerial license to operate this equipment may be
required in certain areas. Consult your national authority for possible
requirements. Changes or modifications not expressly approved
by Shure Incorporated could void your authority to operate the
equipment. Licensing of Shure wireless microphone equipment is
the user's responsibility, and licensability depends on the user's
classification and application, and on the selected frequency. Shure
strongly urges the user to contact the appropriate telecommunications
authority concerning proper licensing, and before choosing and
ordering frequencies.
Information to the user
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Australia Warning for Wireless
This device operates under an ACMA class licence and must comply
with all the conditions of that licence including operating frequencies.
Before 31 December 2014, this device will comply if it is operated in
the 520-820 MHz frequency band. WARNING: After 31 December
2014, in order to comply, this device must not be operated in the 694-
820 MHz band.
Note: EMC conformance testing is based on the use of supplied and
recommended cable types. The use of other cable types may degrade
EMC performance.
Please follow your regional recycling scheme for batteries, packaging,
and electronic waste.
8