Publicité
Les langues disponibles
Les langues disponibles
electric tools are switched off. Having a finger on
the switch when carrying the electric tool or when the
machine is on when plugging it may lead to injuries.
If you wish to work outdoors with an electric tool,
only use extension cables which are approved for
outdoor use and are marked accordingly. Using an
extension cable suitable for outdoor use reduces the
risk of electric shock.
Be careful, pay attention to what you are doing
and use common sense when working with
electric tools. Do not use electric tools when you
are tired or under the influence of drugs, alcohol
or pharmaceuticals. A moment if inattention when
using electric tools may lead to serious injuries.
Check the machine for any damage. Before using
the equipment again, the protective equipment
must carefully be checked if safe and working as
designated.
Check the moving parts for perfect functioning, if
working smoothly and if no parts are damaged. To
provide safe operation of the equipment, all parts
must be installed properly and meet all conditions.
Damaged protective equipment and parts must be
professionally repaired or replaced by a recognised
professional workshop, unless otherwise specified
in the Operating Instructions.
Damaged switches must be replaced in a customer
service workshop.
Do not use electric tools with a defective switch.
An electric tool that cannot be switched on or off is
dangerous and must be repaired.
Have your electric tool repaired by an electrician.
This electric tools complies with the relevant safety
regulations. Repairs may only be carried out by an
electrician using genuine spare parts; otherwise the
user may suffer accidents.
WARNING The use of other tools and other accessories
may pose an injury risk for you.
Safety instructions Circular table
saw
Operation is only allowed with a safety
switch against stray current (RCD max. stray
current of 30mA).
Use protective equipment. Always wear safety
glasses when working with the machine. The use of
protective clothing is recommended, such as dust
mask, protective gloves, sturdy non-slip footwear
and ear defenders. Wear ear protectors. Exposure to
noise can cause hearing loss.
Wear gloves when handling saw blades and rough
materials. Transport and store the tools in a suitable
container;
Warning The dust produced when using this tool may
be harmful to health. Do not inhale the dust. Use
a dust absorption system and wear a suitable dust
protection mask. Remove deposited dust thoroughly,
e.g. with a vacuum cleaner.
Connect the saw to a dust-collecting device when
sawing wood. Dedusting device must be put in
operation prior the work start.
Before use check machine, cable, and plug for any
damages or material fatigue. Repairs should only be
carried out by authorised Service Agents.
Always use the protective shields on the machine.
For security, use devices such as safety- and pressure
device, guide slide, rip fence, etc.
During round timber cutting it is necessary to fix the
workpiece against rotation by means of fixing tool
and use circular saw type suitable for cross cuts.
Do not use circular saws for cutting slots (grooves in
workpiece).
Cutting rebates or grooves is only permitted with a
suitable protective device fi tted, e.g. a protective
tunnel over the saw table.
Support large panels to minimise the risk of blade
pinching and kickback. Large panels tend to sag un-
der their own weight. Supports must be placed under
the panel on both sides, near the line of cut and near
the edge of the panel.
Warning Sawdust and splinters must not be removed
while the machine is running.
In the event of a blockage, switch off the machine
immediately. Pull out the mains plug and remove the
jammed workpiece.
Replace the table insert when worn
Do not use saw blades which are damaged or
deformed
The teeth thickness, or the set of the teeth must be
thicker than the body of the blade and the riving
knife. Do not remove the riving knife.
It is necessary to select a saw blade which is suitable
for the material being cut.
Do not use saw blades not corresponding to the key
data given in these instructions for use.
Es dürfen nur Sägeblätter verwendet werden, die EN
847-1 entsprechen.
Die Sägeblätter müssen in einem geeigneten Behält-
nis transportiert und aufbewahrt werden.
Only use saw blades which have been properly
sharpened. It is essential to adhere to the maximum
speed specified on the saw blade.
The rated speed of the accessory must be at least
equal to the maximum speed marked on the power
tool.
Stecken Sie den Schiebestock oder das Schiebeholz
bei Nichtgebrauch in seinen Halter.
Verwenden Sie einen Schiebestock oder ein Schie-
beholz, um das Werkstück am Sägeblatt vorbei zu
führen.
The handle lock must always be engaged when
transporting the circular table saw. Do not use the top
protective cover as a handle for transportation!
ENGLISH
31
Publicité
