Maytag Commercial MLE22PD Instructions D'installation page 34

ELECTRONIC CONTROL SETUP INSTRUCTIONS
C.20 VALUE OF COIN 2 (Washer)
C.20
PD MODELS: This represents the value of
coin 2 in number of nickles. 20 = $1.00.
Increase between 1 and 200 nickles by
pressing the POWERWASH button and
decrease by pressing the TEMPERATURE
button.
C.05
PN models only: For models using Enhanced
Debit, this field represents the value of top
off in nickles for the dryer, or $.25.
Factory default of C.05; represents 5 x $.05,
or $.25.
Press the EXTRA RINSE button once
to advance to next code.
E.00 ADD COINS OPTION (Washer)
This option is either selected On or not
selected Off. This option causes the customer
display to show the number of coins (Coin
1) to enter, rather than the dollars-and-cents
amount.
E.00 Not selected Off.
E.AC Selected On.
Press DELICATES button three consecutive
times for this selection.
PN models only: In enhanced debits mode,
this option is not selectable.
Press the EXTRA RINSE button once
to advance to next code.
WASH UPGRADES (Washer)
H.00 COOL Temperature Upgrade Price—
COOL
Set between 0 and 200 by pressing the
POWERWASH (increase) button or pressing
the TEMPERATURE (decrease) button.
Factory preset for 0 coins = $0.00.
H.00 WARM Temperature Upgrade Price—
WARM Set between 0 and 200 by pressing the
POWERWASH (increase) button or pressing
the TEMPERATURE (decrease) button.
Factory preset for 0 coins = $0.00.
H.00
HOT Temperature Upgrade Price—Set
HOT between 0 and 200 by pressing the
POWERWASH (increase) button or pressing
the TEMPERATURE (decrease) button.
Factory preset for 0 coins = $0.00.
H.01 EXTRA RINSE Upgrade Price—Set between
EXTRA RINSE
0 and 200 by pressing the POWERWASH
(increase) button or pressing the
TEMPERATURE (decrease) button.
Factory preset for 1 coins = $0.25.
Press the EXTRA RINSE button once to
advance to next code.
J.Cd COIN/DEBIT OPTION (Washer)
J.Cd Both coin and debit selected.
J.d Debit card selected, coins disabled. Press
the DELICATES button three consecutive
times for this selection.
J.C
Coins selected, debit disabled. Press the
DELICATES button three consecutive times
for this selection.
J.Ed
Enhanced Debit is self-selected when a
Generation 2 card reader is installed in the
Washer. The Ed option cannot be manually
selected or deselected.
Press the EXTRA RINSE button once to
advance to next code.
34
L.00 PRICE SUPPRESSION OPTION (Washer)
This option causes the customer display to
show "ADD" or "AVAILABLE" rather than the
amount of money to add. (Used mainly in
debit installations.)
L.00 Not selelcted Off.
L.PS Selected On. Press the DELICATES button
once for this selection.
Press the EXTRA RINSE button once
to advance to next code.
n.CE CLEAR ESCROW OPTION (Washer)
When selected, money held in escrow for
30 minutes without further escrow or cycle
activity will be cleared.
n.CE
Selected On.
n.00
Not selected off. Press the DELICATES
button once to deselect this selection.
Press the EXTRA RINSE button once to
advance to next code.
r.800 TOP SPIN SPEED RPM (Washer)
r.800 This can be selected from the following spin
speeds: 600 rpm, 750 rpm, 800 rpm, 1000
(displays as 999) rpm. Step between speeds
by pressing the DELICATES button. Factory
default of 800 rpm.
Press the EXTRA RINSE button once
to advance to next code.
U.00 PENNY INCREMENT OFFSET (DRYER)
U.00 This represents the penny increment price
offset used in Generation 2 (Enhanced Debit)
PN models. Choose from 0-4 pennies by
pressing the HEAVY DUTY button.
U.00 COIN (HUNDREDTH) INCREMENT OFFSET
(Washer)
U.00
This represents the penny increments price
offset used in Generation 2 (Enhanced Debit)
PN models. Increase from 0-4 pennies by
pressing the POWERWASH button decrease
by pressing TEMPERATURE button.
Press the EXTRA RINSE button once to
advance to next code.
CYCLE SETTINGS (Washer)
A1.03 PREWASH LENGTH
This is the number of minutes of PREWASH.
Set between 2 and 7 by pressing the
POWERWASH (Increase) button or pressing
the TEMPERATURE (decrease) button.
Press the EXTRA RINSE button once to
advance to next code.
A2.03 FINAL SPIN LENGTH
This is the number of minutes of final high-
speed spin. Set between 3 and 8 by pressing
the POWERWASH (increase) button or
pressing the TEMPERATURE (decrease)
button.
Press the EXTRA RINSE button once to
advance to next code.