SLV MERVALED S Mode D'emploi page 3

ENGLISH
OPERATING MANUAL FOR
WALL LUMINAIRE
232405
Read this short manual carefully and keep it accessible for further
reference!
SAFETY MESSAGES
Disregard of the safety messages may lead to danger of life, burning or
fire!
 Installation, mounting or works on the electrical connection may only be
carried out by an approved electrician.
 The product may not be modified or converted.
 Do not hang or fasten anything on the product, especially no decoration.
 Do not cover the product - provide free air circulation.
 The luminaire may only be operated with a complete and intact protection
glass.
 In case of a malfunction you may NOT touch the product or operate it
further. Disconnect the product from the power supply by an external
switch or by the fuse.
A malfunction exists when:
 visible damages appear.
 the product does not work properly (e.g. flickering).
 smoke, steam or crackling sounds appear.
 smell of burning is recognisable.
 an overheating is recognisable (e.g. by discolouration of adjacent
surfaces).
Operate the product only after maintenance and examination by an
approved electrician!
 This product is not intended to be used by children. Ensure that children do
not suffer any harm e.g. by burns from hot surfaces or by electrical shock.
Additional safety messages are indicated by this symbol:
USE AS DIRECTED
This product serves exclusively lighting purposes and may:
 only be used with a voltage of 220-240V ~50/60Hz.
 only be installed according to safety class I (one).
 only be operated when firmly mounted on a stable, even and tilt-fixed
surface.
 only be operated on normally or not flammable surfaces.
 not be exposed to strong mechanical loads or to strong contamination.
MAINTENANCE AND CARE
Light source
 The light source of this luminaire may only be replaced by the
manufacturer, an authorized service technician or a comparable qualified
person.
Care
 The following enviromental influences may have unwanted effects on the
surface of the product:
 acid rain and sour soil, high salt content in the air
 cleaning agents, fertilizer especially in flowerbeds
 thawing salt, other chemical substances (e.g. herbicides)
Protect the product by adequate means to avoid unwanted changes of
the surface.
Disconnect the product from the power supply and let it cool down, before
you clean the product.
 Clean the product on a regular basis using a slightly moistened, soft and fluff-
free cloth. Please also note additional supplied notes on maintanance and
care.
STORAGE AND DISPOSAL
Storage
 The product must be stored in a dry and clean environment. Do not strain
the product mechanically during storage.
After a damp or soiling storage the product may only be installed after
checking its condition by an approved electrician.
Disposal (European Union)
 Do not dispose the product with the regular household waste! Products
marked with this sign must be disposed according to the directive (WEEE,
2012/19) on electrical and electronic devices at local collection points for such
devices!
INSTALLATION
(only by an approved electrician)
Switch off the mains or respectively the connection lead before doing any
works!
Use only parts, which are supplied with the product or are described as
accessories!
Inspect the product for loose parts inside the housing. When there are loose
parts inside the housing and these are not explicitly described the product may
not be installed or operated.
Use the supplied fastening material only when it is suited for the installation
background. If this is not the case use only fastening material suiting the
installation background.
Unpacking
.
 Carefully take the product out of the packaging removing any transport
safeguards.
 Before disposal of the packaging material make sure that all components of
the product are removed.
Installation place
 The product is solely suited for installation on a wall.
 LED react sensitive on high temperatures! Before installation pay attention to
the expected temperature at the place of operation. This may not exceed the
allowed ambient temperature (ta=40°C) of the product.
The product may only be utilized according to IP54.
IP54: Protection against disturbing dust deposition - Protection against
splashing water from all directions.
Prepare the power supply lead according to valid rules for outdoor
installations.
Do not seal the product yourself, using additional silicon or another sealant.
Installation steps (read completely before installation)
 Install the luminaire as shown in the figure.
 The product may not be exposed to direct sunlight when in operation.
 Electrical Connection
 The product must be able to be separated by an all pole separation from
the current supply.
 Direct the connection lead with its complete insulation through the cable
entry into the housing.
 Equip the three wire ends with protective tubes.
 For electric connection attach the black or brown wire (live conductor)
of the connection lead with the clamp L and the blue wire (neutral
conductor) of the connection lead with the clamp N. The green-yellow
wire (protective conductor) of the connection lead has to be tightly
connected with the earth clamp of the product.
Detection Adjustment:
Sets the
Light Control
10 - 2000 Lux
luminosity on
(Day Mode)
which the sensor
reacts.
position, the
sensor starts
at any time.
Sets the
Sensibility
sensitivity of the
sensor.
position, the
sensor has
sensitivity.
Time Setting
Sets the
5" 30" 1' 3' 5' 8'
operating time of
To set a certain time slide the
the luminaire.
"
= Seconds
respective Dip switch into the
'
= Minutes
Sensor test:
- Slide the Dip switch 5" into the position "on". All other switches are in the
position „off".
- Switch on the luminaire. The sensor is ready for operation.
- Activate the sensor. The luminaire turns on and turns off again after 5
seconds.
- Switch the light control switch into the position „night mode".
Activate the sensor by daylight. The luminaire does not switch on.
Activate the sensor in darkness. The luminaire turns on and turns off
again after 5 seconds.
Check if the product functions properly and is securely fixed!
art.-no. 232405 © 21.11.2017 SLV GmbH,
Daimlerstr. 21-23, 52531 Übach-Palenberg, Germany,
Tel. +49 (0)2451 4833-0
Technical Details are subject to change.
<10 Lux
(Night Mode)
In this In this
position, the
sensor starts
at night only.
low
high
In this
In this
position, the
sensor has
high
low sensitivity.
off on
position „on".