BEGLEC JB SYSTEMS LED OCTO PANEL Mode D'emploi page 5

ENGLISH
 Once the correct channel mode shows on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Show mode
Used to select one of the preprogrammed shows with their associated playback speed.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select the desired show:
(show9) or (auto fade).
 Once the desired show is shown on the display, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
 Once the desired show is selected, you will be asked to choose the playback speed: display blinks while
showing .
 Use DOWN and UP buttons to select the desired speed: SP01 (slow) to SP08 (fast).
 No need to confirm, just use the MENU button to go back to the main menu.
Blackout Mode
Blackout mode: when no DMX-signal is detected, the unit goes in blackout and waits for the DMX-signal.
No blackout mode: when no DMX-signal is detected, the unit automatically switches to standalone mode.
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP button to select
(yes blackout) or
 Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Led Display
Display on: display is always on.
Display off: display is off when not used.
 Press the MENU button until the display shows
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select
(display always on) or
 Once the mode is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
To go back to the functions without any change press the MENU button again.
Color setup mode
Used to set a predefined or self-made color on all 8 panels:
This is how to set the colors:
 Press the MENU button until
is shown on the display.
 Press the ENTER button, the display starts blinking.
 Use DOWN and UP buttons to select the desired color:
(manual color) mode.
 Once the desired color is selected, press the ENTER button to save it.
(or automatically return to the main functions without any change after 8 seconds)
 When
(manual color mode) was selected, you will be able to set the values of the 3 basic colors
independently. Toggle through the 3 colors using the ENTER button:
 Red color (display shows:
) : Use DOWN and UP buttons to set the value (0~255) of this color,
confirm with the ENTER button.
 Green color (display shows:
) : Use DOWN and UP buttons to set the value (0~255) of this
color, confirm with the ENTER button.
 Blue color (display shows:
) : Use DOWN and UP buttons to set the value (0~255) of this color,
confirm with the ENTER button.
JB SYSTEMS
®
OPERATION MANUAL
(random show), (show1) to
(no blackout) mode.
.
(display off when not used).
(color 1) to (color 9) or
5/49 LED OCTOPANEL
ENGLISH
To go back to the functions without any change press the MENU button again.
Display Inversion
Display normal: display is readable when the unit is on the floor.
Display inversion: display is readable when the unit is mounted upside down.
 Press the MENU button untill
is blinking on the display. (normal display)
 Use the ENTER button to change to the mode
stored after 8 seconds. Or press the ENTER button again return to the mode
 To go back to the functions press the MENU button.
OPERATING INSTRUCTIONS
 Once connected to the mains the device starts running.
 Do not switch the unit on and off in short time intervals as this reduces the lamp life.
 Always unplug the unit when it is not used for a longer time or before servicing.
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 Important: Don't use the effect in the presence of persons suffering from epilepsy.
You can operate the unit in 4 ways:
 Standalone 1unit
 By master/slave built-in preprogram function
 By OC-1 controller
 By CA-8 easy controller
 By universal DMX controller
1. Standalone 1unit:
Important! This mode only works when the blackout mode in the menu is set to OFF, otherwise
nothing will happen! Read more about this option in the "Main Menu" paragraph.
Just connect the unit to the mains, choose the desired preprogrammed show and put on some music.
The unit will start working automatically to the rhythm of the music.
2. By master/slave built-in preprogram function:
Important! This mode only works when the blackout mode in the menu of the master is set to
OFF, otherwise nothing will happen! Read more about this option in the "Main Menu" paragraph.
Select this function when you want an instant show. By linking the units in master/slave connection, the
first unit will control the other units to give an automatic, sound activated, synchronized light show. Its
DMX input will have nothing plugged into it, its master-LED will be constantly on and sound-LED will
flash to the music.
To automatically set the DMX addresses of the fixtures: Press the MENU button of the first unit until
is blinking on the display, then press the ENTER button and the DMX512 addresses of all the
fixtures will automatically be set.
3. Controlled by OC-1 controller:
OC-1 is a special matrix controller developed to control the LED OCTOPANEL very easily: no need for
time consuming DMX-programming, just plug and play!
 Two 8x8 matrixes (16 LED OCTOPANEL) can be controlled at once!
JB SYSTEMS
®
OPERATION MANUAL
(display inversion), the option will be automatically
(normal display).
6/49 LED OCTOPANEL