Earthing; Height Adjustment; Smoke Exhaust System - Palazzetti TERMOPALEX A VASO CHIUSO Notice D'installation

5 mm
2 m
30/96
5 mm
- 6.3a -
5 mm
0, 5 cm
B
B
A
- 6.3b -
A
0,4 m
- 6.4 -
INSTALLATION
6.2

EARTHING

The Termopalex is equipped with a screw for the
equipotential connection which can hold a cable with a
section from 2.5 mm
equipotentiality of the earth in compliance with current
VWDQGDUGV 7KLV ¿[WXUH LV ORFDWHG RQ WKH ORZHU SDUW RI WKH
Termopalex and is indicated by the symbol
$OVR WKH ÀXH PXVW EH ¿WWHG ZLWK D RZQ HDUWK LQ FRPSOLDQFH
to the standards in force.
6.3

HEIGHT ADJUSTMENT

7R DGMXVW WKH ¿QDO KHLJKW RI WKH 7HUPRSDOH[ FODGGLQJ
¿UH EHG KHLJKW  MXVW WXUQ WKH DGMXVWPHQW VFUHZV ORFWHG
on the base. Adjsut the screws (Fig. 6.3a: A-adjustment
VFUHZ %¿UH EHG KHLJKW  XQWLO WKH PDUEOH FRYHU SUR¿OH
on the Termopalex is at the proper height compared to
WKH FODGGLQJ PDNLQJ VXUH WKDW WKH ERWWRP RI WKH ¿UHSODFH
LV OHYHO )RU FODGGLQJ ZLWK ¿UH EHG +  FP UHPRYH WKH
adjustment screws. Where featured, the lever for the
adjustment of combustion air must be about 0.5 cm over
the cladding surface, so that it is easily usable. (Fig. 6.3b).
6.4

SMOKE EXHAUST SYSTEM

The Termopalex must be connected to a smoke exhaust
system so as to ensure combustion products are suitably
discharged into the atmosphere, in accordance with
standards EN 1856-1-2 EN 1857, EN 1443 EN 13384-
1-3, EN 12391-1 and UNI 10683, both as regards sizing
and the construction materials used.
‡ The CHIMNEY must be sized as described on the
datasheet (average draught 12 Pa with door closed).
‡ The components making up the combustion
product exhaust system must be declared as being
VXLWDEOH IRU WKH VSHFL¿F RSHUDWLQJ FRQGLWLRQV DQG
marked.
‡ 7KH ÀXH PXVW KDYH D FRQVWDQW FURVVVHFWLRQ DORQJ
its entire height.
‡ The minimum recommended height is 3.5 to 4 m
(Fig. 6.4).
‡ A collection chamber should be featured at the bottom of
WKH ÀXH WR FROOHFW DQ\ VROLG UHVLGXHV DQG FRQGHQVDWH
,03529,6(' ÀXHV PDGH XVLQJ XQVXLWDEOH PDWHULDOV DUH
illegal and affect correct operation of the Termopalex.
‡ A PERFECT DRAUGHT LV DERYH DOO WKH UHVXOW RI D ÀXH
that is clear of obstructions such as chokes, horizontal
sections or corners; any axial displacements should be
at a maximum angle of 45° compared to the vertical axis,
(better still if it is only 30°). These displacements should
preferably be effected near the chimney top (Fig. 6.5).
‡ The SMOKE FRQQHFWLRQ EHWZHHQ WKH ¿UHSODFH DQG
ÀXH VKRXOG KDYH WKH VDPH FURVV VHFWLRQ DV WKH VWRYH¶V
VPRNH RXWOHW 7KH VPRNH ¿WWLQJ PXVW EH VHDOHG DQG WKH
XVH RI ÀH[LEOH PHWDOOLF SLSHV LV SURKLELWHG &KDQJHV LQ
direction in respect to the smoke outlet of the appliance
must be executed using elbows not exceeding 45° in
respect to vertical.
‡ The CHIMNEY TOP shall be the WINDPROOF type
with an inside cross section equivalent to that of the
ÀXH DQG ZLWK D VPRNH RXWOHW SDVVDJH VHFWLRQ DW OHDVW
DOUBLE WKH LQWHUQDO RQH RI WKH ÀXH.
cod. 004772420 TMPX VC - 10/2013 - Palazzetti - PN - Italy
2 to 6 mm 2 , to be used to obtain
.