Initial Operation, Setting - Metabo KSE 55 Vario Plus Notice Originale

en ENGLISH
Use suitable accessories for special work. In this
way, fewer particles enter the environment in an
uncontrolled manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits,
- use an extraction unit and/or air purifiers,
- ensure good ventilation of the workplace and keep
clean using a vacuum cleaner. Sweeping or
blowing stirs up dust.
Vacuum or wash the protective clothing. Do not
blow, beat or brush.
5. Overview
See page 2.
1 Marking (saw blade outer diameter)
2 Cutting indicator
3 Movable guard
4 Parallel stop
5 Locking screws (diagonal cuts)
6 Locking screws (parallel guide)
7 Locking button (switching on)
8 Trigger (switching on and off)
9 Nozzle (chip ejection)
10 Adjusting screws for zero-play sliding on guide
rail (guide rail not included in scope of delivery,
see chapter on Accessories)
11 Scale (diagonal cut angle)
12 Lock nut (adjust saw blade angle)
13 Adjusting screw (adjust saw blade angle)
14 Cable guide
15 Rotational speed preselection wheel
16 Signal display
17 Lever (for swivelling back the movable guard)
18 Depot for hexagon wrench
19 Hexagon spanner
20 Locking screw (for setting cutting depth)
21 Clamping lever (for setting cutting depth)
22 Cutting depth stop (for setting cutting depth) and
cutting depth indicator
23 Scale (depth of cut)
24 Handle
25 Auxiliary handle
26 Spindle locking button
27 Inner saw blade flange
28 Saw blade
29 Saw blade fixing screw

6. Initial Operation, Setting

Before plugging in, check to see that the rated
mains voltage and mains frequency, as
specified on the rating label, match your power
supply.
Always install an RCD with a max. trip current
of 30 mA upstream.
Pull the plug out of the plug socket before any
adjustments or servicing are performed.
12
6.1 Setting cutting depth
Note: It is advisable to set the depth of cut in such a
way that no more than half of each tooth on the saw
blade juts out under the workpiece. See illustration
on page 2.
- Release locking screw (20). Lift motor section
against guide plate (depth of cut = 0 mm).
- Preselect the desired depth of cut with the cutting
depth stop (22), see illustration, page 2. To do
this, release the clamping lever (21), set the
cutting depth stop (22) on the scale (23) to the
desired depth of cut and clamp the clamping lever
again.
- Press the motor section downwards as far as the
stop.
- Tighten locking screw (20) again.
Note: the clamping power of the locking screw (20)
can be adjusted. Unscrew the screw on the lever to
do this. Remove lever and mount offset
counterclockwise. Secure with screw. When doing
this, note that the cutting depth setting device
moves freely when the lever is open.
6.2 Slanting saw blade for diagonal cuts
Loosen the two locking screws (5) to make the
setting. Tilt the motor section against the guide
plate. Read the angle which has been set from the
scale (11). Retighten the front and then the rear
locking screw (5).
6.3 Correcting the saw blade angle
The saw blade angle is set ex works.
If, at 0°, the saw blade is not at right angles to the
guide plate: release locking screws (5). Release
lock nut (12) and correct saw blade angle with
adjusting screw (13). Then retighten the lock nut.
Retighten both locking screws (5).
6.4 Rotational speed preselection
Select the speed at the setting wheel (15). For
recommended speeds, see page 3.
6.5 Setting extraction nozzle / chip ejection
Sawdust extraction:
remove nozzle (9) if necessary. To extract the
sawdust, connect a suitable extraction unit with
suction hose to the machine.
Sawdust ejection:
Fit nozzle (9) and turn in desired direction (away
from body if possible).
7. Use
7.1 Switching on and off
Switching on: Press locking button (7) and hold in;
then actuate the trigger (8).
Switching off: Release the trigger (8).
7.2 Signal display
The signal display (16) lights up briefly when the
machine is switched on and indicates operational
readiness. If the signal display lights up during