System Status Menu; Main Menu; Input Setup Menu - Rotel RSP-1066 Manuel D'utilisation

SYSTEM STATUS Menu

SYSTEM STATUS
LISTEN: Tuner
RECORD: VIDEO 1
MODE: Stereo
INPUT: Analog
VOLUME: 45
ZONE: Off
ENT KEY=MAIN MENU
OSD KEY=EXIT
The SYSTEM STATUS menu provides a snap-
shot of the current system settings and a start-
ing point for reaching all other screens and
menus. This screen appears when you press
the MENU button on the remote control and
displays the following information:
LISTEN: the source selected for listening.
RECORD: the source selected for the VIDEO
and AUDIO outputs.
MODE: the current surround sound mode.
INPUT: the input selected for the current source:
Optical, Coaxial, Analog, etc.
VOLUME: the current volume setting.
ZONE: the current status of ZONE 2, ON or
OFF.
No changes can be made using this screen;
it only provides information. To go to the rest
of the menus, press the ENTER button to go
to the MAIN menu. Press the MENU key on
the remote to cancel the display and return
to normal operation.
: The SYSTEM STATUS screen appears
NOTE
for ten seconds when the unit is turned on
and automatically turns off.
25

MAIN Menu

MAIN MENU
INPUT SPEAKER
DELAY TEST TONE
SUB LEVEL ZONE 2
OTHER DEFAULT
ENT KEY=ENTER
UP KEY=up DWN KEY=down
The MAIN menu provides access to eight other
screens and menus and is reached by press-
ing the ENTER button from the SYSTEM STA-
TUS menu described above or from most other
menus. To go to another menu, move the high-
light to the desired line using the UP/DOWN
buttons on the remote and press the ENTER
button. Press the MENU key on the remote to
cancel the display and return to normal op-
eration.

INPUT SETUP Menu

INPUT SETUP
LISTEN: Video 2
INPUT LABEL: _ _ _ _ _
INPUT: Coaxial 2
SURR MODE: Dolby 3 Stereo
ENT KEY=MAIN MENU UP KEY=up
+/– KEY=change DWN KEY=down
The INPUT SETUP menu configures the source
inputs and is reached from the MAIN menu.
The screen provides the following options, se-
lected by placing the highlight on the desired
line using the UP/DOWN buttons:
LISTEN: changes the current listening input
source (CD, TUNER, TAPE, VIDEO1, VIDEO2,
VIDEO3, VIDEO4, VIDEO5).
INPUT LABEL: The labels for the five VIDEO
inputs can customized (not available for the
TUNER, CD, and TAPE inputs). Place the high-
light on this line to call up a sub-menu that al-
lows you to change the five-character label
for the current VIDEO source. To change the
label:
1. Press the +/– keys to begin labeling.
2. Press the +/– keys to change the first let-
ter, scrolling through the list of available
characters.
3. Press the ENT key to confirm that letter and
move to the next position.
4. Repeat steps 2 and 3 until all five charac-
ters have been completed. The final press
of the ENT button will save the new label
and exit the sub-menu.
INPUT: selects which physical input connec-
tion to use as the default for the source dis-
played in the first line of the menu. The op-
tions are ANALOG inputs, two OPTICAL digital
inputs (OPTICAL 1& 2), and three COAXIAL
digital inputs (COAXIAL 1 – 3). When a digi-
tal input is selected, the unit will check for a
digital signal when the INPUT SOURCE but-
ton is pressed. If no digital signal is present,
the unit will automatically revert to the ana-
log input. When an ANALOG input is selected,
the unit will not access a digital signal, even
though one may be present at the digital in-
put; thus, the ANALOG setting forces the unit
to use accept only an analog signal. Assign-
ing a digital input (with its auto-sensing) is the
preferred configuration for digital source in-
puts such as DVD players.
: If a source connected to a digital input
NOTE
is selected, that signal will automatically be
sent to both digital outputs for recording.
SURR MODE: selects the default surround
sound mode for the input shown at the top of
the menu. The default setting will be used unless
the source material triggers automatic decoding
of a particular type or unless the default set-
ting is overridden by the front panel or remote
surround buttons. Options are: Stereo, Dolby
Pro Logic II, Dolby 3-Stereo, Music 1 – 4, 5CH
Stereo, 7CH Stereo, and DTS Neo:6.
This is a default setting for each input and, in
some cases, can be manually overridden by
the front-panel MODE buttons or the SUR+
button on the remote. See the SURROUND
SOUND CONTROLS section of this manual
for more information on which settings can be
overridden.
: The following types of discs or source
NOTE
material are generally detected automatically
and the proper decoding activated with no
action or setting required: DTS, DTS-ES Ma-
trix 6.1, DTS-ES Discrete 6.1, Dolby Digital,
Dolby Digital Surround EX, Dolby Digital 2-
channel, PCM 2-Channel, MP3, and HDCD.
English