Video 1-3 Audio Outputs; Video 1-3 S-Video Outputs; Digital Source Connections; Digital Inputs - Rotel RSP-1066 Manuel D'utilisation

VIDEO 1–3 Audio Outputs
Using standard audio interconnect cables,
connect the left and right channel RCA audio
outputs from the RSP-1066 to the audio inputs
on the source component. Make sure that you
are consistent. If you hook up a VCR to the
VIDEO 1 inputs, hook up the VIDEO 1 out-
puts to the same VCR. Also make sure that the
left channel is connected to the LEFT connec-
tors and the right channel to the RIGHT con-
nectors.
VIDEO 1–3
Composite Video Outputs
If you choose to use the RCA composite video
connections for a source component, use a
75 ohm video interconnect cable to connect
the RSP-1066's RCA video output (labeled
COMPOSITE OUT) to the RCA video input on
your VCR.
VIDEO 1–3 S-Video Outputs
If you choose to use S-Video connections for
a source component, use an S-Video cable
to connect the RSP-1066's S-Video output (la-
beled S-VIDEO OUT) to the S-Video input on
your source component.

Digital Source Connections

See Figure 4.
The RSP-1066 provides digital connections
which may be used in place of, or in addi-
tion to, the analog audio input and output con-
nections described in the previous sections.
These connections include five digital inputs
and two digital outputs for recording.
These digital connections can be used with
any source component that supplies a digital
signal, such as a DVD player or CD player.
: A digital connection means that the digi-
NOTE
tal processors in the RSP-1066 will be used
to decode the signal, rather than the source
component's internal decoders. In general,
you must use digital connections for a DVD
player or other component that supplies a
Dolby Digital or DTS signal, otherwise the
RSP-1066 will not be able to decode these
formats.
21

Digital Inputs

The RSP-1066 accepts digital input signals from
source components such as CD players, sat-
ellite TV receivers, and 5.1 channel Dolby
Digital, DTS, or 6.1 channel DTS ES signals
from DVD players. The built-in D/A converter
senses and adjusts to the correct sampling rates.
There are five digital inputs on the rear panel,
three coaxial and two optical. These digital
inputs can be assigned to any of the input
sources using the INPUT MENU screen de-
scribed later in this manual. For example, you
can assign the COAXIAL 1 digital input con-
nector to the VIDEO 1 source and the OPTI-
CAL 2 digital input to the VIDEO 3 source.
Connect the appropriate cable (optical or 75
ohm coaxial) from the digital output of your
source component to a digital input on the
RSP-1066 and then configure that digital in-
put for use with the source component using
the INPUT MENU.
: When using digital connections, you
NOTE
should also make the analog audio input con-
nections described previously. The analog
connection is necessary to record to an ana-
log recorder or for ZONE 2 operation

Digital Outputs

The RSP-1066 has a digital output (with a choice
of coaxial or optical connectors) to send the
digital signal from any of the five digital in-
puts to a digital recorder or outboard digital
processor. When a digital input source sig-
nal is selected for listening, that signal is au-
tomatically sent to both digital outputs for re-
cording or outboard processing.
: Only digital signals from source com-
NOTE
ponents are available at these outputs. Ana-
log signals cannot be converted and are not
available at the digital outputs.
Connect the digital output to the digital input
of your recorder or processor. You can use
either a 75 ohm coaxial video cable or an
optical cable.

Output Signal Connections

See Figure 3.
This section of the manual describes the au-
dio and video signal output connections on
the RSP-1066. These are used for routing the
output signals to television monitors, audio am-
plifiers, and recording devices.

TV Monitor Output

The video output of the RSP-1066 sends the
video signal to your TV monitor. Three types
of video output connections are provided –
RCA composite video, S-Video, and Compo-
nent Video. Choose the type of video output
connection that matches the type of video input
connections you have made. Connect the TV
MONITOR output , from either RCA compos-
ite or S-Video or Component Video connec-
tor, to the corresponding input on your televi-
sion monitor, using appropriate video cables.
: The RCA composite video output only
NOTE
sends signals from RCA composite video
source inputs to the TV monitor. The S-Video
output only sends signals from S-Video video
source inputs to the TV. The Component Video
output only sends signals from Component
Video source inputs to the TV. If you have
connected all of your source components with
the same type of connection, then you only
need to make one connection from the
RSP-1066 to the TV monitor. However, in a
mixed system with, for example, some S-Video
and some RCA composite inputs, you will
need to make two connections to the TV moni-
tor and use its input selector to switch be-
tween the two when changing sources.
: The ON-SCREEN DISPLAY system is not
NOTE
available when using Component Video con-
nections to the TV monitor
English