Learning Commands - Marmitek PowerMid Plus Mode D'emploi

ENGLISH
3. Enter a random 3 digit VCR code from the Library Code
Tables. The LED turns off after the last digit has been entered
4. Now you are able to start the manual or automatic code
search for this mode button
When your device cannot be found in the code list, or your device
doesn't respond to any of the codes you entered, you can try to find
the code required by using the 'searching for codes' method:
1. Turn on the device you want to control.
2. Press and hold SETUP until the LED indicator lights steadily.
Release SETUP button.
3. Press the mode button (TV, VCR, etc.) that matches the equip-
ment you wish to control. The LED blinks once.
4. Press CHANNEL+ repeatedly* until the device to be controlled
changes channel. If you go past the code accidentally press REW
to step back (for the first step push button twice).
5. Press and release the ENTER button to complete the set-up.
*Note: You may have to press CHANNEL+ many times (50+). If the
device does not have a Channel Up function, use the PLAY button
(VCR only) or the POWER button.
AUTOMATIC CODE SEARCH:
IMPORTANT:
To select the correct code library section for manual or automat-
ic code search, select a random code from the code list for the
type of device you are looking for (e.g. VCR, SAT, DVD, etc.).
E.g. Auto search for VCR:
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button
2. Press and release the mode button (VCR, CBL, etc.) you
want to use for controlling your VCR
3. Enter a random 3 digit VCR code from the Library Code
Tables. The LED turns off after the last digit has been entered
4. Now you are able to start the manual or automatic code
search for this mode button
When searching an unknown code, you can step through the library
automatically (AutoSearch). When your equipment responds, you can
stop the searching process and store the code you found.
1. Turn on the device you want to control.
2. Press and hold SETUP until the LED indicator lights steadily.
Release SETUP button.
3. Press the mode button (TV, VCR, etc.) that matches the equip-
ment you wish to control. The LED blinks once.
5. Press CHANNEL+ once. After a few seconds the remote starts
stepping through the code library (fast search). When the device
responds, you press CHANNEL- to switch to slow search. You can
step back by pressing CHANNEL- (you can step forward by press-
ing CHANNEL+ in case you went too far back). As soon as the
device responds again, press ENTER to store the code you
found.
8
IDENTIFYING CODES FOUND USING THE SEARCH
PROCEDURE:
1. Press and hold SETUP until the LED indicator lights steadily.
Release the Set-up button.
2. Press the mode button that matches the equipment you wish to
identify. The LED blinks once.
3. Press and release SETUP. The LED blinks once.
4. To find the first digit, press each number button from 0 to 9 until
the LED blinks. The number you pressed is the first digit of the
code.
5. Press each number button from 0 to 9 as above to find the sec-
ond digit.
6. Press each number to find the third digit. When the third digit has
been found, the LED will go out. Write down the code you found
on the label inside the battery compartment.
LEARNING
Your Marmitek MultiMedia Remote has the codes for most TV's,
VCR's etc. in its code library. However, if the code for your particular
device is not found in the library, you can learn these codes from your
existing remote. Or if you find a code from the tables in this manual
that "almost" matches your device, but a few buttons are missing, you
can learn just those buttons.

LEARNING COMMANDS:

1. Point your existing remote at the Marmitek MultiMedia Remote
(front to front) with a distance of about 2,5 centimetres between
the remotes.
2. Press and hold SETUP until the LED indicator lights steadily.
3. Press the mode button (TV, CD, SAT, etc.) that matches the
equipment you wish to learn. The LED blinks once.
4. Press and release the LEARN button. The LED blinks once.
5. Press and release the button on the Marmitek MultiMedia Remote
that you want to teach. The LED blinks once. (Press SHIFT first to
learn a shifted function).
6. Depending on the type of original remote, you can use choose
one of two methods:
a. Press the button on your original remote that you want to learn.
Hold the button until the LED on the Marmitek MultiMedia Remote
blinks off shortly. When the LED blinks off more than once, you
have to use method b. (note: if you just tried method a, return to
step 5 before choosing method b).
b. Press the button which you want to learn of your original
remote as long as your would do during normal operation of
your device.
7. Repeat steps 5 and 6 for each button you want to learn.
8. When you're finished learning all the keys, press SETUP.
CLEARING LEARNED COMMANDS TO FREE UP MEMORY:
You can clear learned commands for each device individually (TV,
VCR. Etc.):
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
2. Press the desired mode button (TV, VCR, etc.). The LED flashes once.
3. Press and release the LEARN key twice.
4. Press the SETUP key. The LED will turn off after a few seconds.
5. All learned commands entries under that mode are now cleared.
ENGLISH
9