Marmitek PowerMid Plus Mode D'emploi page 4

ENGLISH
[8] Showview/V+
This key gives you control over the VideoPlus or ShowView functions
of your VCR (only when your VCR supports this function). When your
VCR does not have this function, this key can give you access to
timer functions or the menu of the VCR.
When using the Showview/V+ key in other modes than VCR (TV,
CBL, SAT, CD), this key usually is used for the SCAN function. This
allows you to zap between channels or listen to the intro's on a CD.
The key gives a channel up or skip command every 3 seconds. You
can stop the SCAN function by pressing any key. The SCAN functions
stops automatically after 2 minutes.
[9] Marmitek X-10 button:
Lets you control Marmitek X-10 Home Automation Modules to operate
lamps and appliances throughout your home.
0 - 9:
Used as your original remote and to enter device codes.
[10] A · B:
Used for toggle functions (pre-programmed mode).
[11] Ent (Enter):
Used in conjunction with the numeric keys for direct channel tuning. In
set-up mode used to confirm.
[12] Info:
Works in the same way as your original remote.
[13] Channel:
Works like your original remote. Also used to switch Marmitek X-10
Home Automation Modules on and off.
[14] OK/Mute:
Works the same way as your original remote. Also used to switch all
Marmitek X-10 Home Automation Modules off.
[15] Volume:
Works like your original remote. Also used to brighten and dim lights
connected to Marmitek X-10 Lamp Modules.
[16] M1, M2
Macro keys. Lets you execute a pre-programmed string of IR com-
mands.
[17] L1, L2:
Lets you learn additional keys from your original remote.
[18]
Teletext HOLD. Holds the current page.
[19]
Teletext MIX. Mixes the text with the TV program on the background.
[20] Play, FF, Stop, Rew, Pause:
Works the same as on your original remote. Also function as Fast Text
colour keys.
[21]
Teletext ON.
6
[22] REC:
Record button. Works the same as your original VCR remote. You
must press the REC button twice to begin recording.
[23]
Teletext OFF.
CLEARING THE MEMORY (RECOMMENDED ON FIRST TIME SET-UP):
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
2. Press and release the STOP key twice.
3. Press the MUTE key. The LED will turn off after a few seconds.
4. All code entries and learned command entries are now cleared.
SETTING UP FOR TV, VCR, DECODER, CD, DVD AND SATELLITE
RECEIVER
1. Turn on the device you wish to control (TV, VCR, satellite receiver,
CD etc.).
2. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button.
3. Press and release the mode button that matches the device you
want to control (TV, VCR, CD, etc.).
4. Enter the 3 digit code from the Library Code Tables. The LED
turns off after the last digit has been entered.
5. Point the remote at the device and press the POWER button. Your
device should turn off.
6. Turn your device on and press CHANNEL+. If the device
responds, set-up is complete. If some buttons do not operate your
equipment, try one of the other codes for your brand.
FLEXMODE:
It is recommended to program a CD under the CD button, Video
under VCR button, etc. However, except for the TV button, all other
device buttons can be programmed as you wish, i.e. VCR under CD,
SAT under CBL, etc, allowing you to program more than one CD,
VCR, etc.
NOTES:
If your TV, VCR, Satellite Receiver does not respond, try the other
codes for your brand. If it still doesn't respond, try the Code Search
method.
If the LED blinks rapidly when you enter the code, you may have
entered an invalid code. Recheck the code in the code list and try again.
MANUAL CODE SEARCH:
IMPORTANT:
To select the correct code library section for manual or automat-
ic code search, select a random code from the code list for the
type of device you are looking for (e.g. VCR, SAT, DVD, etc.).
E.g. Auto search for VCR:
1. Press and hold SETUP until the LED indicator lights steadily.
Release the SETUP button
2. Press and release the mode button (VCR, CBL, etc.) you
want to use for controlling your VCR
ENGLISH
7