Publicité
provide him/her with the Operating Instructions. Keep the
Operating Instructions for future reference!
Package: The appliance has been put in a package to prevent
any damage during transport. Packages are raw materials so
they can be reused or recycled.
Please read carefully the Operating Instructions and follow
them. Use these Operating Instructions to get acquainted with
the appliance, its corresponding use and safety instructions.
Keep the Instructions for future reference.
•
Inspect the appliance visually before each use. Do not use
the appliance if any safety device is damaged or worn out.
Never remove any safety device.
•
Use the appliance only for the purpose specified in these
Operating Instructions.
•
Be always careful when working. Watch your activity.
Proceed carefully. Do not use the cable reel if you are not
concentrated.
•
Safety in the workplace is your responsibility.
•
Never leave the appliance unattended.
•
Do not use the appliance when raining or in a humid or wet
environment
•
Do not use electric tools near flammable liquids or gases.
•
Do not switch the appliance on if turned over or not in the
operating position.
•
Keep the appliance out of reach of other persons,
especially children and pets.
•
Do not let other persons touch the appliance or cable.
•
After you finish working with the appliance, pull the plug
out of socket and check if the appliance is not damaged.
•
Any repairs can only be executed by an electrician.
•
Before putting the appliance into operation and after any
impact check it for any wear-out or damage and have
necessary repairs executed.
•
Never use spare parts and accessories not recommended
by the producer.
•
Use the appliance only in broad daylight or under sufficient
artificial lighting.
•
Wear protective clothing suitable for the given environment
the whole time you work and take suitable preventive
measures to prevent accidents.
•
Do not use the cable for any other purpose than specified.
Do not wear the cable by its cable and do not use the
cable for pulling the plug out of socket. Protect the cable
against excessive temperatures, oil and sharp edges.
•
Be very careful of your appliance. Keep it clean so that
working with it is fine and safe. Regularly check the plug
and cable and have them repaired by an authorised
specialist if damaged. Regularly check the extension
cables and have any damaged cable replaced by a
specialist.
•
Extension cables to be used outdoors only. For outdoor
work, use extension cables adequately marked and
approved for that purpose (within 20 m ∅1.5 mm², 20-50 m
∅ 2.5 mm²)
•
Unplug the appliance
- before every cleaning
- after each use
•
Before connecting the machine to the mains make sure that
the power supply voltage is that as shown on the plate or
that the difference, if any, is not more than 10%. If the
source voltage does not correspond to that requited for the
machine, the result may be a serious injury or damage to the
machine.
•
Avoid any bodily contact with grounded objects (such as
pipes, radiators, stoves and refrigerators). The risk of
electric shock increases if your body is grounded.
•
Wear proper working clothing. Do not wear any wide
garments or jewellery. If your hair is long, wear a hairnet.
Keep the clothing and gloves outside the reach of the
machine moving parts. Wide garments, jewellery and long
hair could get stuck in the rotating parts.
•
Avoid an unintended switching of the machine. Before
plugging the machine, make sure that it is off. Carrying the
machine with a finger on the ON/OFF switch or plugging
a machine that is on will increase the risk of injury.
•
Do not use a machine with a defective ON/OFF switch.
The machine that cannot be put on and off any more is
dangerous and should be repaired.
•
Persons unable to operate the appliance due to their
physical, sensory or mental abilities or their
inexperience or lack of knowledge must not operate
it.
•
If the appliance show any sign of visible damage the
appliance must not be put into operation.
•
If the feeder cable of the appliance is damaged it
needs to be replaced by the producer or an
electrician.
•
Repairs of the appliance can only be executed by an
electrician. There might be significant risks as a
result of unauthorised repairs.
•
The same regulations apply for accessories.
Güde GmbH & Co. KG does not answer for damages
caused by:
•
Appliance damage by mechanical influences and
overloading.
•
Any changes to the appliance.
•
Use for any other purpose than that described in
the Operating Instructions.
•
Unconditionally follow all safety instructions to
prevent accidents and damage.
Important safety instructions
•
If the power cable gets damaged or broken during the
work, do not touch it and unplug the machine
immediately. Never use the machine with a defective
cable.
•
The dust produced at work may be harmful to health,
flammable or explosive. Therefore, it is necessary to
take appropriate protective measures. Many types of
dust are carcinogenic, for example. Use a suitable dust
extractor and wear a mouth guard. The light metal dust
may burn or explode.
•
Always connect the machine via fault current circuit
breaker (FI-) with starting current of 30 mA max.
•
Hold the machine by the insulated handgrips if the tool
inserted could get in contact with a hidden conductor or
the power cable. A contact with a live conductor may
cause conductivity of the machine metal parts and thus
an electric shock.
•
Never stand atop of the machine. It may cause serious
injuries when it rolls over or if you accidentally touch the
cutting tool.
•
Use a cutting disc, the permissible speed of which is at
least the same as the machine idling speed. Check the
cutting disc before use.
•
Never stand in front of the machine aligned with the disc.
Always stand at the side of the cutting disc. Your body is
better protected against fractions if the cutting disc
breaks.
•
The cutting disc should be fitted perfectly and should
turn freely. Have a trial run without any load for 1 minute
at least. Do not use a disc that is damaged, non-circular
or vibrating.
•
Set up the depth stop properly. If the stop is not set up
correctly, the disc may cut the surface under the base
plate.
•
During the operation, the cutting disc cover should be in
place and the swinging protective cover should work as
appropriate.
•
Do not cut any material with asbestos or magnesium
content.
•
Protect the disc from any blows, hits and grease.
•
Do not conduct the machine to the work piece unless it
is on.
•
Keep your hands out of the reach of the rotating disc.
10
Publicité
