ST E 300 Li 40 Série Manuel D'utilisation page 109

Tondeuse à gazon alimentée par batterie et à conducteur à pied
Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 160
WARNING!: READ THIS MANUAL CAREFULLY BEFORE
EN
USING THE MACHINE. Keep safe for future use.
INDEX
1. GENERAL INFORMATION .......................................... 1
2. SAFETY REGULATIONS ............................................. 2
3. ABOUT THE MACHINE ................................................ 4
3.1
Machine description and intended use ............... 4
3.2
Safety signs ......................................................... 4
3.3
Identification label .............................................. 4
3.4
Main components ................................................ 5
4. ASSEMBLY ................................................................... 5
4.1
Assembly components ....................................... 5
4.2
Grass catcher assembly ..................................... 5
4.3
Handle assembly ................................................ 5
5. CONTROLS .................................................................. 6
5.1
Safety key (Deactivation device) ........................ 6
5.2
Switch command ................................................. 6
5.3
Cutting height adjustment ................................... 6
6. USING THE MACHINE ................................................. 6
6.1
Preliminary operations ........................................ 6
6.2
Safety checks ...................................................... 7
6.3
Start-up ............................................................... 7
6.4
Operation ............................................................ 7
6.5
Stop ..................................................................... 8
6.6
After use .............................................................. 8
7. ROUTINE MAINTENANCE .......................................... 8
7.1
General Information ............................................ 8
7.2
Battery ................................................................. 9
7.3
Cleaning .............................................................. 9
7.4
Nuts and bolts ..................................................... 9
8. OCCASIONAL MAINTENANCE ................................... 9
8.1
Cutting device ................................................... 10
9. STORAGE................................................................... 10
9.1
Storing ............................................................... 10
9.2
Storing the battery ............................................. 10
10. HANDLING AND TRANSPORT ................................. 10
11. ASSISTANCE AND REPAIRS .................................... 10
12. WARRANTY COVERAGE ...........................................11
13. MAINTENANCE TABLE ..............................................11
14. TROUBLESHOOTING............................................... 12
15. ACCESSORIES ON REQUEST ................................. 12
15.1 "Mulching" kit..................................................... 12
15.2 Batteries ............................................................ 12
15.3 Battery charger ................................................. 12
1.
GENERAL INFORMATION
1.1
HOW TO READ THIS MANUAL
Some of the paragraphs in this manual contain
particularly important information in terms
of safety and operation, and are highlighted
differently, according to the following criteria:
NOTE or IMPORTANT These give details or further
information on what has been previously indicated and aim
to prevent damage to the machine or cause other damage.
symbol represents a danger. Failure to
The
observe the warning can lead to possible personal
and/or third party injury and/or damage.
The paragraphs highlighted in a dotted grey square
indicate optional characteristics not available on
all models documented in this manual. Check if
the characteristics are available on this model.
Whenever reference is made to a position on the
machine "front", "back", "left" or "right" hand side,
this refers to the operator's working position.
1.2
REFERENCES
1.2.1
Figures
The figures in these instructions for
use are numbered 1, 2, 3, etc.
Components shown in the figures are marked A, B, C, etc.
Reference to component C in figure 2 is indicated with
the wording: "See fig. 2.C" or simply "(Fig. 2.C)".
The figures are provided by way of example. The actual
pieces can differ from those illustrated in this document.
1.2.2
Titles
The manual is arranged in chapters and paragraphs.
The title of paragraph '2.1 Training" is a sub-title of "2.
Safety regulations". References to titles or paragraphs
are marked with the abbreviation chap. or par. and the
relevant number. Example: "chap. 2" or "par. 2.1"
EN - 1

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

E 340 li 40 sérieE 380 li 40 série

Table des Matières