Roller Blade Cleaning; Extended Periods Of Disuse - Sammic FMI-31 Mode D'emploi

required thickness (run a few tests to
correctly perform this operation).
· Adjust the position of the scale counter-
weight according to the size and weight
of the dough to be rolled (run a few tests
to correctly perform this operation).
· Make sure the roller blades are in the
correct position and their springs are
well-tensioned (PICT. 8).
· Turn on the main switch (PICT. 7) on
position (1).
· Press the green button START (PICT. 7) or
press down the pedal control (optional),
to turn on the machine.
· Introduce the small ball of dough made
with flour and left to rise for at least 5
hours, through the opening of the highest
cover (PICT. 7). It is recommended to
squash the sides slightly so the
dough can easily go through the highest
rollers.
· When finished, stop the machine pressing
the button STOP (PICT. 7)
· At the end of the work-cycle, disconnect
the power supply turning the main switch
(PICT. 7) on position (0).
IMPORTANT
Do not insert balls of dough that are more
heavy provided than the weight for each
machine. (see technical specifications pag.
20)
4.2 Recommendations for use
Always use the machine with a wide
opening between the upper rollers to
prevent excessively straining
transmission components.
4.3 Pedal control (Optional)
· When the machine is off, insert the pedal
control plug in the socket on the side of
the appliance.
· Press the start button to power the pedal.
· Start the machine pressing down on the
pedal control. Release the pedal to stop
the machine.
· The machine will restart each time the
pedal is pressed down.
· When finished, turn off the pedal control
by pressing the stop button.
WARNING!
To prevent the appliance from accidentally
restarting, always turn off the pedal by
pressing the stop button. Only remove the
pedal plug from the socket after pressing
the stop button.
5 - MAINTENANCE - TROUBLE SHOOTING
- DEMOLITION
WARNING!
Before doing any kind of maintenance or
cleaning you must take out the plug. In any
case of malfunctioning or damages of the
machine you must apply for authorized
assistance from the manufacturer.
5.1 Cleaning
· Remove the plug from the electrical
socket.
· Accurately clean using neutral products.
· Clean external machine parts with a damp
sponge.
· Do not use metallic pads and abrasive
detergents.
ball of
5.2

Roller blade cleaning

· Unhook the springs on the lower rollers
by pushing them outwards (PICT. 8).
· Rotate the pins inwards and clean the
roller blades with a damp cloth.
· To return the roller blades to their initially
position, follow the above directions in
reverse order.
INFORMATION
Before each work cycle make sure the roller
blades are correctly fastened (PICT. 8).
5.3

Extended periods of disuse

Extended periods of disuse, turn off the
main wall switch, clean the machine and
cover it with a cloth to protect it from dust.
the
5.4. Possible anomalies and breakdown
In the event
malfunctioning, turn off the wall fuse and
contact your dealer's service center. Avoid
dismantling internal machine parts. The
manufacturer is not liable for any machine
tampering.
The machine does not start
·Main switch off
·Turn on the main switch on position I
·No voltage on the power supply
· Contact your dealers's service center
·Safety fuse burnt out
·Contact your dealers's service center
Rollers malfunctioning
·Trasmission parts broken
· Contact your dealers's service center
5.5
The
constructed to work for an average of
10.000 hours.
When finished using the machine, follow
national laws for disposal and recycling.
of breakdown or
O
PERATING TEMPERATURE
E
NERGY SUPPLY
L
OADING
D
OUGH WEIGHT
P
IZZA DIAMETER
D
IMENSIONS
- Width
- Depth
- Height
N
ET WEIGHT
Disposal and recycling
machine was designed
SPECIFICATIONS FMI-31
+15 / +45 Cº
230V / 50Hz
375 W
80 - 210 g
140 - 300 mm
420 mm
450 mm
650 mm
35 Kg
ENGLISH
and
FMI-41
375 W
210 - 700 g
140 - 400 mm
520 mm
450 mm
712 mm
45 Kg
5