Ec-Type Examination Certificate - Dräger PIR 7000 Notice D'utilisation
Masquer les pouces
Voir aussi pour PIR 7000:
- Notice d'installation (54 pages) ,
- Notice d'utilisation (307 pages)
Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Zulassung
EC-TYPE EXAMINATION CERTIFICATE
[1]
Equipment or Protective System intended for use
[2]
in Potentially Explosive Atmospheres
Directive 94/9/EC
DEMKO 07 ATEX 0654417X
[3]
EC-Type Examination Certificate Number:
Gas Sensor Type IDS 01xx
[4]
Equipment or Protective System:
Dräger Safety AG & Co. KGaA
[5]
Manufacturer:
Revalstrasse 1, 23560 Lübeck, Germany
[6]
Address:
[7]
This equipment or protective system and any acceptable variation thereto are specified in the schedule to this certificate and the
documents therein referred to.
[8]
UL International Demko A/S, notified body number 0539 in accordance with Article 9 of the Council Directive 94/9/EC of 23 March 1994,
certifies that this equipment or protective system has been found to comply with the Essential Health and Safety Requirements relating to
design and construction of equipment and protective systems intended for use in potentially explosive atmospheres given in Annex II to
the Directive.
The examination and test results are recorded in confidential report no
[9]
Compliance with the Essential Health and Safety Requirements has been assured by compliance with:
EN 60079-0:2012+A11:2013
EN 60079-1:2007
[10]
If the sign "X" is placed after the certificate number, it indicates that the equipment or protective system is subject to special conditions for
safe use specified in the schedule to this certificate.
[11]
This EC-Type examination certificate relates only to the design, examination and tests of the specified equipment or protective system in
accordance to the Directive 94/9/EC. Further requirements of the Directive apply to the manufacturing process and supply of this
equipment or protective system.
These are not covered by the certificate.
[12]
The marking of the equipment or protective system shall include the following:
II 2 G
Ex d IIC T6/T4 Gb
This is to certify that the sample(s) of the Equipment described herein ("Certified Equipment") has been
investigated and found in compliance with the Standard(s) indicated on this Certificate, in accordance with the
Certification Manager
Certification Manager
ATE
ATEX Equipment Certification Program Requirements. This certificate and test results obtained apply only to
the e
the equipment sample(s) submitted by the Manufacturer. UL did not select the sample(s) or determine whether
Jan-Erik Storgaard
Jan-Erik Storgaard
th
the
the
the
the
th
the
the sample(s) provided were representative of other manufactured equipment. UL has not established Follow-
the
the
th
he
h
h
he
he
he
he
h
he
he
h e
he
h
h
he
h
h e
e
e
e
e
e
e
s
U
U
U
U p S
U
Up Service or other surveillance of the equipment. The Manufacturer is solely and fully responsible for
U
U
U
U
U
U
U
U
U
U
U
U
U
U
c
c
c
c
c
c
c
c
c
c
c
c
c onf
c
conformity of all equipment to all applicable Standards, specifications, requirements or Directives. The test
resu
results may not be used, in whole or in part, in any other document without UL's prior written approval.
Date of issue: 2007-10-04
Da
Re-issued: 2014-12-17
No
No
No
N
No
N
No
No
No
No
N o
No
No
N
No
No
No
N
No
N o
No
No
No
N
No
No
No
No
N o
No
No
No
No
N
No
Notified Body
N o
No
No
N
No
N o
No
o
o
o
o
o
o
o
o
o
t
ti
t
t
t
t
t
t
t
t
t
t
t
t
t
fied Body
UL
UL International Demko A/S, Borupvang 5A, 2750 Ballerup, Denmark
Te
Tel. +45 44 85 65 65, info.dk@ul.com,
00-IC-F0056 – Issue 8.3
This certificate may only be reproduced in its entirety and without any change, schedule included.
Rev.3
. 4786604806
EN 60079-1:2014
www.ul.com
Page 1 of 3
455
Publicité
Table des Matières
