Before Use; Safety Instructions - BEGLEC JB SYSTEMS DUALSCAN Mode D'emploi

ENGLISH
Thank you for buying this JB Systems product. To take full advantage of all possibilities
and for your own safety, please read these operating instructions very carefully before you
start using this unit.
FEATURES
This unit is radio-interference suppressed. This product meets the requirements of the
current European and national guidelines. Conformity has been established and the
relevant statements and documents have been deposited by the manufacturer.
• This device has been designed to produce decorative effect lighting and is used in light
show systems.
• Two independent DMX scanners in one compact housing
• Can be installed on any horizontal surface.
• Just connect the small, optional CA-8 controller for easy operation
• Master/slave mode with built-in programs + micro
• Easily controlled with iLEAD, SM1612 or any other DMX controller
• 2x 10 multi colored Gobos
• Gobo Shaking effect
• Blackout and variable strobe
• DMX control 8 channels: (2x pan, 2x tilt, 2x shutter/gobo shaking, 2x gobo/color)
• Fan cooling and electronic overheat protection.
• Adjustable focus

BEFORE USE

• Before you start using this unit, please check if there's no transportation damage. Should
there be any, do not use the device and consult your dealer first.
• Important: This device left our factory in perfect condition and well packaged. It is
absolutely necessary for the user to strictly follow the safety instructions and warnings in
this user manual. Any damage caused by mishandling is not subject to warranty. The
dealer will not accept responsibility for any resulting defects or problems caused by
disregarding this user manual.
• Keep this booklet in a safe place for future consultation. If you sell the fixture, be sure to
add this user manual.
Check the contents:
Check that the carton contains the following items:
• DUALSCAN
• Mains cable
• 2x EFP 100W/12V lamp
• Operating instructions
JB SYSTEMS®
OPERATION MANUAL
1/40 DUALSCAN
ENGLISH

SAFETY INSTRUCTIONS:

• To protect the environment, please try to recycle the packing material as much as
possible.
• A new light effect sometimes causes some unwanted smoke and/or smell. This is normal
and disappears after some minutes.
• To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
• To avoid condensation to be formed inside, allow the unit to adapt to the surrounding
temperatures when bringing it into a warm room after transport. Condense sometimes
prevents the unit from working at full performance or may even cause damages.
• This unit is for indoor use only.
• Don't place metal objects or spill liquid inside the unit. Electric shock or malfunction may
result. If a foreign object enters the unit, immediately disconnect the mains power.
• Locate the fixture in a well ventilated spot, away from any flammable materials and/or
liquids. The fixture must be fixed at least 50cm from surrounding walls.
• Don't cover any ventilation openings as this may result in overheating.
• Prevent use in dusty environments and clean the unit regularly.
• Keep the unit away from children.
• Inexperienced persons should not operate this device.
• Maximum save ambient temperature is 45°C. Don't use this unit at higher ambient
temperatures.
• The units' surface temperature may reach up to 85°C. Don't touch the housing with bare
hands during its operation.
• Make sure the area below the installation place is free from unwanted persons during
rigging, de-rigging and servicing.
• Allow the device about 10 minutes to cool down before replacing the bulb or start
servicing.
• Always unplug the unit when it is not used for a longer time or before replacing the bulb
or start servicing.
• The electrical installation should be carried out by qualified personal only, according to
the regulations for electrical and mechanical safety in your country.
• Check that the available voltage is not higher than the one stated on the rear panel of the
unit.
• The power cord should always be in perfect condition: switch the unit immediately off
when the power cord is squashed or damaged.
• Never let the power-cord come into contact with other cables!
• This fixture must be earthed to in order comply with safety regulations.
• Don't connect the unit to any dimmer pack.
• Always use an appropriate and certified safety cable when installing the unit.
• In order to prevent electric shock, do not open the cover. Apart from the lamp and mains
fuse there are no user serviceable parts inside.
• Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a
fuse of the same type and electrical specifications!
• In the event of serious operating problems, stop using the fixture and contact your dealer
immediately.
• The housing and the lenses must be replaced if they are visibly damaged.
• Please use the original packing when the device is to be transported.
• Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
JB SYSTEMS®
OPERATION MANUAL
2/40 DUALSCAN