Cleaning And Maintenance - Royal Catering RCKV-AMS Manuel D'utilisation

First start up.
1. Unpack the whole appliance.
2. Make sure that no packing material has been left in
the compressor chamber.
3. Remove all documents and other accessories from
the inside of the appliance.
4. Install all additional components of the appliance.
5. Align wheel chocks to prevent the device from
moving or ensure it is on a level surface.
6. Clean and dry the interior
7. Close the door of the appliance.
8. Connect the appliance plug to the socket.
9. Set refrigeration according to requirements.
10. Load the device once the pre-set temperature has
been reached.
Height adjustment / levelling:
Do adjust the height or level the device, slightly screw out
(but not entirely) or in device feet.
ASSEMBLING THE DEVICE
• Installing the glass shelf
It is possible to install a glass shelf in the device. To do so,
proceed as follows:
1. Bolt the supports to the glass cover, on the left and
on the right side.
2. Bolt the supports to the glass shelf, on the left and
on the right side.
3. Bolt the glass shelf to the pin fitted in the centre of
the upper part of the glass cover.
• Installing transparent sliding door
The included transparent sliding door must be installed in
the device. This will make it easier to maintain the required
temperature inside the device.
The sliding door consists of three parts.
– left – with a left-hand side opening and a guide at
the top
– middle – slightly higher, with opening on both
sides and a guide at the top
– right – with a right-hand side opening and a guide
at the top
1. Install the left door, first inserting it into the
lower guiding rail, located closer to the inside
of the device, and then into the top one,
located closer to the inside of the device.
2. Install the right door, first inserting it into the
lower guiding rail, located closer to the inside
of the device, and then into the top one,
located closer to the inside of the device.
3. Install the middle door, first inserting it into
the lower guiding rail, located further from the
inside of the device, and then into the top one,
located further from the inside of the device.
• Installing two glass covers
The glass covers are to be fitted inside the slot, located
behind the oblong fan, located near the front glass cover.
The covers should be installed horizontally and slightly
tilted towards the foodstuffs displayed in the device.
• Changing the door opening direction
It is possible to change the direction of the door opening
in the bottom section of the device. To do so, proceed as
follows:
1. Undo the bolts that connect the hinges to the
enclosure of the device.
2. Remove the door and turn them upside down, or
swap the left and the right door.
10
3. Bolt the door with the hinges to the enclosure of the
device.
TURNING THE DEVICE ON
1. Close the door of the device
2. Make sure that the device switch is in the [O] position
and plug the power lead of the device to the mains.
3. The device will start operation once it is plugged to
the mains, but the controller of the device remains
inactive until it is activated with the I/O switch.
4. Put the I/O switch in the [I] position to turn on the
controller of the device. The current temperature
inside the device will be displayed.
The device will start cooling down to the preset temperature,
and will cyclically defrost a certain number of times per day,
depending on the value set in the programming mode (by
default, every 4 hours).
CONTROL PANEL DESCRIPTION
1 2
1. Device controller
2. On/Off button (I/O respectively)
DEVICE CONTROLLER OPERATION:
Button functions
Displaying settings. In service
programming mode – select
parameter and conform
changes.
Enables lighting
Scroll list of parameters (in
service programming mode)/
Increase set value
Scroll list of parameters (in
service programming mode)/
Decrease set value/Enables
manual defrosting
BUTTON COMBINATIONS
Lock/unlock buttons
Initiate service programming
mode – ATTENTION! IT IS
RECOMMENDED NOT TO
INITIATE THE SERVICE MODE –
all the factory parameters were
set in this mode and changes
may result in incorrect device
operation.
Return to ambient temperature
display.
Rev. 11.01.2018
SYMBOL MODE DESCRIPTION
ON Compressor is active
Flashing Prevention of short operation
periods activated
ON Active defrosting
Flashing Active dripping
ON Unit of temperature
Flashing Programming mode
ON Unit of temperature
Flashing Programming mode
DISPLAYING SETTINGS
1. Briefly press the SET button and the current setting
will be displayed.
2. To return to the standard screen briefly press SET or
wait for approximately 5 seconds.
CHANGING SETTINGS
1. Press and hold down the SET button
approximately 3 seconds
2. The current setting will be displayed and °C or °F
diode will flash.
3. Change the setting using or .
4. To accept changes press the SET button.
MANUAL DEFROST
The device shall require a defrost if internal ice build-up
occurs. This may happen due to too frequent opening of
the doors for long periods.
Press and hold down the button for at least 5
seconds – defrost will start and an appropriate message
will appear in the display.
ATTENTION: Manual defrost resets the automatic defrost
schedule. The next automatic defrost will start 4 hours after
manual defrost ends.
ATTENTION! Do not use electrical devices (such as a hair
dryer) or open fire to defrost the device. Plastic elements
of the interior may melt and a spark or flame may ignite
the fumes.
LOCKING BUTTONS
Press and hold down the and buttons for at
least 3 seconds. „OF" will be displayed – the buttons are
now locked.
UNLOCKING BUTTONS
Press and hold down the and buttons for at
least 3 seconds. „on" will be displayed – the buttons are
now active.
TRANSPORTATION AND STORAGE
During transport, the machine should be protected from
shaking, falling and turning upside down. Store it in
a properly ventilated place with dry air and without any
corrosive gas. All the glass elements are to be transported
with extra caution. For transport, they must be wrapped in
such a way as to prevent damage.
Rev. 11.01.2018

CLEANING AND MAINTENANCE

It is recommended to wash the appliance regularly. Before
start of cleaning of the appliance or before performance
of any repair or maintenance work, it is necessary to
disconnect the appliance from the power supply and
wait until it has cooled down. Do not use for washing any
caustic cleaners, such as cleaning powders, agents with
alcohol content, thinners, diluents, etc., and do not allow
water to enter the appliance interior. Never immerse the
appliance, cord or plug in water or any other liquid. It is
forbidden to clean the device with a water jet. The interior
of the device should be cleaned with a disinfectant suitable
for the food industry. To clean, use a damp, soft cloth and
then dry thoroughly. Dry the surface with a soft, dry cloth.
The following actions should be taken if the machine is not
used for a long period of time: Disconnect the appliance
completely from the power supply and remove all food
products from it. Then wash the entire appliance with
a damp, soft cloth and mild cleaning agent, rinse with clean
water and dry thoroughly, for some time leave the door
open, so that the appliance will be completely dry. From
time to time, check that the cable is not damaged. Do not
use the appliance if the cable is damaged. A damaged cable
must be replaced by a service or a qualified electrician. In
the event of damage or malfunction, please contact your
dealer or our service. Maintenance and repair work must
be done only by qualified personnel using original spare
for
parts and accessories. Attempts to make repairs on your
own can lead to a direct threat to life or health, and will
void the warranty!
Remember to regularly remove dust and dirt from the
condenser. Significant soiling of the condenser may
damage the device. Clean the condenser with moist, soft
cloth. Remove stubborn stains, e.g. grease, with a neutral
detergent. The device must be dried after each cleaning.
Regularly inspect the water drain hole, to ensure it is not
jammed by deposited dirt or other objects. The drain pipe
must be regularly checked for leaks.
CHECK REGULARLY THE DEVICE
Check regularly that the device doesn ́t present any
damage. If there is any damage, please stop using the
device. Please contact your customer service to solve the
problem.
What to do in case of a problem?
Please contact your customer service and prepare following
information:
• Invoice number and serial number (the latter is to be
found on the technical plate on the device).
• If relevant, a picture of the damaged, broken or
defective part.
• It will be easier for your customer service clerk to
determine the source of the problem if you give
a detailed and precise description of the matter.
The more detailed your information, the better the
customer service will be able to answer your problem
rapidly and efficiently!
CAUTION: Never open the device without the authorization
of your customer service. This can lead to a loss of warranty!
11