Scheppach 5903405901 Traduction Des Instructions D'origine page 20

• Check the connection cable of the electric tool reg­
ularly and have it replaced by a recognised special­
ist when damaged.
• Check extension cables regularly and replace them
when damaged.
• Keep the handle dry, clean and free of oil and
grease.
15. Pull the plug out of the outlet
• Never remove loose splinters, chips or jammed
wood pieces from the running saw blade.
• During non­use of the electric tool or prior to main­
tenance and when replacing tools such as saw
blades, bits, milling heads.
• When the saw blade is blocked due to abnormal
feed force during cutting, turn the machine off and
disconnect it from power supply. Remove the work
piece and ensure that the saw blade runs free. Turn
the machine on and start new cutting operation
with reduced feed force.
16. Do not leave a tool key inserted
• Before switching on, make sure that keys and ad­
justing tools are removed.
17. Avoid inadvertent starting
• Make sure that the switch is switched off when
plugging the plug into an outlet.
18. Use extension cables for outdoors
• Only use approved and appropriately identified ex­
tension cables for use outdoors.
• Only use cable reels in the unrolled state.
19. Remain attentive
• Pay attention to what you are doing. Remain sensi­
ble when working. Do not use the electric tool when
you are distracted.
20. Check the electric tool for potential damage
• Protective devices and other parts must be care­
fully inspected to ensure that they are fault-free and
function as intended prior to continued use of the
electric tool.
• Check whether the moving parts function faultless­
ly and do not jam or whether parts are damaged. All
parts must be correctly mounted and all conditions
must be fulfilled to ensure fault-free operation of the
electric tool.
• The moving protective hood may not be fixed in the
open position.
• Damaged protective devices and parts must be
properly repaired or replaced by a recognised
workshop, insofar as nothing different is specified
in the operating manual.
• Damaged switches must be replaced at a customer
service workshop.
• Do not use any faulty or damaged connection ca­
bles.
• Do not use any electric tool on which the switch
cannot be switched on and off.
21. Attention!
• The use of other insertion tools and other acces­
sories can entail a risk of injury.
20 | GB
 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58
22. Have your electric tool repaired by a qualified
electrician
• This electric tool conforms to the applicable safety
regulations. Repairs may only be performed by an
electrician using original spare parts. Otherwise
accidents can occur.
m WARNING! This electric tool generates an elec­
tromagnetic field during operation. This field can im­
pair active or passive medical implants under certain
conditions. In order to prevent the risk of serious or
deadly injuries, we recommend that persons with
medical implants consult with their physician and the
manufacturer of the medical implant prior to operat­
ing the electric tool.
Additional safety rules for the oscillating spindle
grinding machines
WARNING: Do not use your machine until it is com­
pletely assembled and installed according to the in­
structions.
• If you are not familiar with the operation of the
sanding machine, ask the head of the department,
your teacher, or any other qualified person.
• ATTENTION: This machine has only been de­
signed for sanding wood or similar materials. The
sanding of other materials can cause fire, injuries,
or damage the product.
• Always wear safety goggles.
• This machine may only be operated indoors.
• IMPORTANT: Mount and use the machine on a
horizontal surface. A non­horizontal surface can
damage the motor.
• If the machine tends to tilt or walk (especially when
sanding long and heavy panels), it must be fas­
tened to a solid surface of sufficient carrying force.
• Firmly hold the workpiece when sanding.
• Do not wear gloves. Do not hold the workpiece with
a cloth during sanding.
• Never sand workpieces too small to be held safely.
• Avoid awkward hand positions where a sudden slip
could cause your hand to touch the sanding belt
or disc.
• When sanding a large piece of material, provide an
additional support at table height.
• Never sand an unsupported workpiece. Secure the
workpiece with the table or the fence. Exceptions
are the sanding of curved workpieces on the out­
side of the sanding disc.
• Always clear the table, fence or sanding belt of
scraps or other objects, before turning the machine
on.
• Do not perform any layout assembly or set-up work
on the table while the sanding machine is in opera­
tion.
• Switch the machine off and pull the power plug from
the socket when fitting or removing accessories.