Boost Feature; Gauge Consumption, Energy Savings - RADSON Flores C E Notice D'utilisation

Mode overview
2
Programming by pilot wire
If you do not want to use the programming feature.
Orders sent by the pilot wire will only be applied in Auto mode, thus your device
will automatically receive and apply the programmed orders sent by your
power manager or your time switches
by pilot wire page 10).
• Comfort mode
Non-stop Comfort mode. The device will
operate 24 hours a day to achieve
the temperature which has been set (e.g.
19°C). The Comfort mode temperature le-
vel can be set by the user (see Setting the
comfort mode temperature page 6).
• Eco mode
Eco, which means the Comfort Mode tem-
perature minus 3.5°C. This enables you to
lower the temperature without having to
reset the Comfort Mode temperature.
Select this mode for shortterm absences
(between 2 and 24h ) and during the night.
• Frost protection mode
This mode enables you to protect your
home against the effects of cold weather
(frozen pipes, etc.), by maintaining a mini-
mum temperature of 7°C
in it at all times. Select this mode when
you will be away from your home for a
long time (more than 5 days).
Restoring factory settings

BOOST FEATURE

Important:
the Boost mode can be enabled at any time, whatever the
current operating mode (Auto, Comfort, Eco or Frost protection).
To activate Boost mode, press
be set at maximum for the time period you request. 60 minutes display
will flash by default.
- First press = Boost.
During the first minute: the boost symbol and the heating indicator ap-
pear and the duration count flash.
auto auto
mode mode
During the first minute, you can modify the Boost duration from 0 to the
maximal authorised duration of the Boost, such as
defined during the advanced settings
intervals of 5 minutes (or more quickly by push superior to 2 seconds) by
pressing and . This modification will be saved and effective for
the next Boost.
After 1 minute, the Boost count begins and the time is running,
minute by minute.
Comment: After 1 minute, you can modify temporarily the duration: it
will be valid only for this active Boost and therefore non-recurring.
Display
(see Information about remote control
auto auto
mode mode
auto auto
mode mode
auto auto
mode mode
See page 14,16 and 19.
boost , the desired temperature setting will
prog prog
boost
OK OK
(see page 13 for more details)
The Boost can stop for 2 different reasons:
- An order "Stop" has been sent by your energy manager through the
pilot wire:
prog prog
The device stops, -- appears. The cursor moves above auto. When the
boost
order Comfort will be sent, the device will be restarted until the count
end.
- If the ambient temperature reaches the maximal Boost temperature
OK OK
during the count:
prog prog
boost
OK OK
The device switches off but the Boost mode is always active : the count
prog prog
is always displayed, the Boost symbol and the heating indicator flash on
the display. When the temperature drops under the maximal authorised
temperature, the device will be restarted until the count ends.
boost
- Second press = Boost cancellation.
OK OK
The cursor moves above the previous active mode and the setting tem-
perature appears.
GAUGE CONSUMPTION, ENERGY
SAVINGS
FRANCE'S AGENCY FOR ENVIRONMENT AND ENERGY MANAGE-
MENT (ADEME) RECOMMENDS A COMFORT SETTING TEMPERATURE
LOWERR OR EQUAL TO 19°C.
In the device display, a selector indicates the energy comsumption level
by positioning it in front of the colour: red, orange or green. So, depen-
ding on the setting temperature, you can choose your level of energy
usage. As the temperature setting
increases, the consumption will be higher.
The gauge appears in Auto, Comfort, Eco and Frost protection modes
and whatever the temperature level.
C - Red colour
High Temperature
level: it is advisable
to significantly
reduce the setting
temperature.
B - Orange colour
Average tempe-
rature level: it is
advisable
to slightly reduce
by
the setting tempe-
rature.
A - Green colour
Ideal temperature.
auto auto prog prog
boost
OK OK
mode mode
auto auto prog prog
boost
OK OK
mode mode
Setting tempera-
ture > 22°C
auto auto
When the setting
temperature is
higher than 22°C
mode mode
19°C < Setting
temperature ≤
22°C
auto auto
When the setting
temperature is
higher than 19°C
and lower or equal
to 22°C
mode mode
Setting tempera-
ture ≤ 19°C
auto auto
When the setting
temperature is
lower or equal to
19°C
mode mode
EN
prog prog
boost
OK OK
prog prog
boost
OK OK
prog prog
boost
OK OK
4