Safety Information - Weller WE 1 Traduction De La Notice Originale

Read these instructions and the safety
guidelines carefully before starting up the unit
and starting work.
Failure to observe the safety regulations results in a risk to
life and limb.
Keep these instructions in a place that is accessible to all
users. Please adhere to the operating instructions of the
connected devices.

Safety information

For safety reasons, children and youths under the age
of 16, as well as persons who are not familiar with these
operating instructions, may not use the device. Children
shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
Keep other persons well away from your workplace.
The work area is out of bounds for children and unauthorised
persons. Never allow other persons to touch the soldering
tool or cable.
WARNING Electrical shock
Connecting the control unit incorrectly poses a risk of
injury due to electric shock and can damage the device.
Carefully read the attached safety information, the safety
•
information accompanying these operating instructions as
well as the operating instructions for your control unit
before putting the control unit into operation and observe
the safety precautions specified therein.
Only connect WELLER tools.
•
If the device is faulty, active electrical conductors may
be bare or the PE conductor may not be functional.
Repairs must always be referred to a Weller-trained
•
specialist.
If the electrical tool's power supply cord is damaged, it
•
must be replaced with a specially prefabricated power
supply cord available through the customer service
organisation.
Protect yourself against electric shocks. The handles on
soldering tools with an antistatic design are conductive.
Avoid touching earthed objects such as pipes, heaters,
•
cookers and refrigerators.
Do not use the soldering tool in a damp or wet environ-
•
ment.
Never work on voltage-carrying parts.
•
Caution! To provide continued protection against risk of
•
electric shock, connect to properly grounded outlets only.
WARNING Risk of burns
Risk of burns from the soldering tool while the control
unit is operating. Tools may still be hot long after they
have been switched off.
The soldering tip becomes very hot during soldering
work. There is a risk of burns from touching the tips.
After the soldering process, the soldering tool and the
workpiece holder are still hot.
Always place the soldering tool in the safety rest while not
•
in use. Make sure the safety holder is stable.
Do not touch the hot soldering tips and keep them away
•
from inflammable objects..
Only replace solder tips when cold
•
Risk of burning through liquid solder. Protect yourself
against solder splashes.
Wear appropriate protective clothing to protect yourself
•
against burns. Protect your eyes by wearing eye
protection.
When working with adhesives, special attention must be
•
paid to the warning information provided by the adhesive
manufacturer.
WARNING Fire hazard
Covering the soldering iron or the safety holder poses
a fire hazard. Always keep objects well away from the
soldering iron and safety holder.
Always keep objects well away from the soldering iron and
•
safety holder.
Keep all combustible objects, liquids or gases well away
•
from the hot soldering tool.
Store your soldering tool in a safe place. When not in
use, units and tools should be stored in a dry, high or locked
area out of the reach of children. Make sure that unused
soldering tools are free of voltage and de-pressurised.
The power cable must only be plugged into the power
socket or adapter approved for this purpose. Check to
see if the mains voltage matches the ratings on the
nameplate. Make sure the machine is switched off before
plugging in.
Do not use the cable for purposes other than those for
which it is intended.Never carry the unit by the cable. Do
not use the cable to pull the plug out of the socket. Protect
the cable against heat, oil and sharp edges..
Be alert. Pay attention to what you are doing. Be smart
when using the unit. Do not use the soldering tool if you are
having difficulty concentrating.
Avoid abnormal posture. Arrange your work station in an
ergonomically correct way. Avoid bad posture when using the
unit, as this can lead to postural problems.
EN
ENGLISH
13