Setting Into Operation; Inserting The Batteries; Switching On The Transmitter; Setting The Transmission Channel - IMG STAGELINE TXS-606LT/2 Mode D'emploi

4 Setting into Operation

4.1 Inserting the batteries

For operating the pocket transmitter, two 1 .5 V batteries
of size AA are required .
•
Always insert (rechargeable) batteries of the same type
and always replace all of them .
•
If the pocket transmitter is not in use for a longer period
of time, always remove the batteries to prevent damage
due to battery leakage .
Never put batteries in the household waste .
Always dispose of the batteries in accordance
with local regulations .
To open the battery compartment (9), press the arrow of
the battery compartment cover (5) and push the cover
downwards . Insert the batteries with the positive and neg-
ative poles as indicated in fig . 2, then replace the cover .

4.2 Switching on the transmitter

Information on the display
To switch on the transmitter, set the switch (2) to ON .
(In the mid-position STDBY the transmitter is on, but the
microphone signal is muted .) The backlight of the display
(3) is activated for a few seconds . The display shows the
following information:
1 . the channel group (GROUP 00 – 07)
2 . the channel (CHANNEL 00 – 99)
3 . the battery status

BATT BATT
■
■
■
■
■
full half-full
Replace the batteries when the indication BATT starts flashing .
Make the settings described in the chapters below .
Remember to switch off the transmitter after use to
prevent discharge of the batteries .

4.3 Setting the transmission channel

1) First set a free transmission channel on the receiver
(see instruction manual of the receiver) .
2) Point the IR sensor (4) of the transmitter towards the IR
window of the receiver . The distance must not exceed
1 .5 m . Make sure that there are no obstacles between
the sensor and the IR window .
3) Briefly press the button ACT on the receiver . The display
backlight of the pocket transmitter is activated . Thus,
the transmitter and the receiver are set to the same

BATT
■
■
■
discharged
channel group and to the same channel (see indication
on the display) . The frequencies assigned to the chan-
nels can be found in the table on page 16 /17 .
4.4 Connecting the tie clip microphone and
attaching the pocket transmitter
1) Connect the plug (12) of the tie clip microphone to the
3 .5 mm jack (6) of the transmitter . To prevent acciden-
tal disconnection, secure the plug with the nut (11) .
2) Attach the tie clip microphone to your clothes, as close
to your mouth as possible .
3) After setting the gain of the microphone signal (chap-
ter 4 .5), use the clip (7) to attach the transmitter to
your clothes (e . g . belt or waistband) .
4.5 Setting the gain of the microphone signal
1) Switch on the audio unit (e . g . mixer, amplifier) con-
nected to the receiver . Speak / sing into the microphone
and set the audio system to such a volume that the
subsequent setting can be heard well .
2) Set the gain of the microphone signal with the control
GAIN (8) on the rear side: If the volume of the micro-
phone signal is too high or if the signal is distorted,
turn back the control with a small screwdriver . If the
volume of the signal is too low, however, a poor sig-
nal-to-noise ratio results . In this case, advance the
control accordingly .
5 Specifications
Carrier frequencies: . . . . . . . 672 .000 – 691 .975 MHz
Frequency stability: . . . . . . . ±0 .005 %
Transmission power (EIRP): . 10 mW
Audio frequency range: . . . 30 – 18 000 Hz, ±3 dB
Power supply: . . . . . . . . . . 2 × 1 .5 V battery, size AA
Operating time: . . . . . . . . . > 8 h
Ambient temperature: . . . . 0 – 40 °C
Dimensions, weight: . . . . . . 61 × 106 × 27 mm, 96 g
Subject to technical modification .
All rights reserved by MONACOR
No part of this instruction manual may be reproduced in any form or
by any means for any commercial use.
for channels see table on
page 16 /17
INTERNATIONAL GmbH & Co. KG.
®
7