Yamaha PLG150-AP Mode D'emploi page 61

1.3.3 All Note Off
This message turns off all notes which are currently on for the corresponding
part.
However, if Hold 1 or Sostenuto are on, notes will continue to sound until these
are turned off.
Control# Parameter
123 All Note Off
1.3.4 Omni Off
Works the same as when ALL Note Off (see 1.3.3) is received.
Control# Parameter
124 Omni Off
1.3.5 Omni On
Works the same as when ALL Note Off (see 1.3.3) is received.
Control# Parameter
125 Omni On
1.3.6 Mono
Perform the same processing as when All Sound Off (see 1.3.1) is received, and
if the value (mono number) is in the range of 0 ... 16, set the corresponding chan-
nel to Mode 4* (m=1).
Control# Parameter
126 Mono
* Mode4 is a state in which only channel messages on the specified channel will
be received, and notes will be played individually (monophonically).
1.3.7 Poly
Perform the same processing as when All Sound Off (see 1.3.1) is received, and
set the corresponding channel to Mode 3* (m=1).
Control# Parameter
127 Poly
* Mode3 is when channel messages will be received only on the specified chan-
nel, and notes will be sounded polyphonically.
1.4 Program change
This message is used to switch voices.
It changes the program number on the receiving channel. When the change is to
include the voice bank, transmit the program change after sending the Bank
Select message (see 1.2.1).
If the Multi Part parameter Rcv PROGRAM CHANGE = OFF, that part will not
receive program changes.
1.5 Pitch bend
This message conveys information on pitch bend operations.
Basically, this message is for changing the pitch of a part, but the depth of the fol-
lowing six effects can be controlled.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. BEND PITCH CONTROL
2. BEND FILTER CONTROL
3. BEND AMPLITUDE CONTROL
4. BEND LFO PMOD DEPTH
5. BEND LFO FMOD DEPTH
6. BEND LFO AMOD DEPTH
By default, the Pitch Control effect is applied.
If the Multi Part parameter Rcv PITCH BEND = OFF, that part will not receive
pitch bend messages.
BEND AMPLITUDE CONTROL is processed on the host device (e.g., MOTIF
ES, MU128, etc.)
1.6 Channel aftertouch
This message conveys the pressure after the key is played on the keyboard (for an
entire MIDI channel). The pressure can be controlled for each part. This message
will affect the notes currently playing.
The effect of this message can be modified by the following parameters.
* Multi Part Parameter
1. CAT PITCH CONTROL
2. CAT FILTER CONTROL
3. CAT AMPLITUDE CONTROL
4. CAT LFO PMOD DEPTH
5. CAT LFO FMOD DEPTH
6. CAT LFO AMOD DEPTH
By default, there will be no effect.
If the Multi Part parameter Rcv CHANNEL AFTER TOUCH = OFF, that part
will not receive Channel Aftertouch.
CAT AMPLITUDE CONTROL is processed on the host device (e.g., MOTIF ES,
MU128, etc.)
Data Range
0
Data Range
0
Data Range
0
Data Range
0 ... 16
Data Range
0
PLG150-AP Owner's Manual / Bedienungsanleitung / Mode d'emploi
2. System exclusive messages
2.1 Parameter changes
This device uses the following parameter changes.
[ UNIVERSAL REALTIME MESSAGE ]
1) Master Volume
[ UNIVERSAL NON REALTIME MESSAGE ]
1) General MIDI System On
[ XG PARAMETER CHANGE ]
1) XG System on
2) XG System parameter change
3) XG Multi Part parameter change
[ PLG150-AP NATIVE PARAMETER CHANGE ]
1) PLG150-AP Native System parameter change
2) PLG150-AP Native Multi Part parameter change
[ OTHER MESSAGE ]
1) Master tuning
2.1.1 Universal realtime messages
2.1.1.1 Master Volume
F0H
11110000
7FH
01111111
* 0xxxnnnn XNH
04H
00000100
01H
00000001
** 0sssssss SSH
TTH
0ttttttt
F7H
11110111
When received, the Volume MSB is reflected in the XG System Parameter
MASTER VOLUME.
* XNH=7FH: Broad Cast
XNH<7FH: N=Device Number, X=Don't Care
The same applies elsewhere.
** The binary expression 0sssssss is expressed in hexadecimal as SSH.
The same applies elsewhere.
2.1.2 Universal non-realtime messages
2.1.2.1 General MIDI System On
F0H
11110000
7EH
01111110
XNH
0xxxnnnn
09H
00001001
00000001 01H
F7H
11110111
When this message is received, the SOUND MODULE MODE is set to XG,
and all data except for MIDI Master Tuning will be restored to the default
value.
Since approximately 50ms is required to process this message, be sure to
allow an appropriate interval before sending the next message.
2.1.3 XG Parameter Change
This message sets XG-related parameters. Each message can set a single
parameter.
The message format is as follows.
F0H
11110000
43H
01000011
1NH
0001nnnn
4CH
01001100
0ggggggg GGH
MMH
0mmmmmmm
LLH
0lllllll
VVH
0vvvvvvv
: :
F7H
11110111
For parameters whose Data Size is 2 or 4, the appropriate amount of data will
be transmitted as indicated by Size.
MIDI Data Format
= Exclusive status
= Universal Real Time
= ID of target device
= Sub-ID #1=Device Control Message
= Sub-ID #2=Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
= Exclusive status
= Universal Non-Real Time
= ID of target device
= Sub-ID #1=General MIDI Message
= Sub-ID #2=General MIDI On
= End of Exclusive
Exclusive status
YAMAHA ID
N:device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
25