Product Familiarisation; Intended Use; Unpacking Your Tool; Before Use - Triton 300W Multi Tool Instructions D'utilisation Et Consignes De Sécurité

p) NEVER start the power tool while the blade or accessory is in contact with the
workpiece, and always allow the power tool to reach its full speed before making
contact with the workpiece. Use the variable speed control of the tool (if fitted) to start the
tool at the correct speed for the accessory or blade fitted.
q) DO NOT exert additional pressure on the body of the tool: allow the blade or
accessory to do the work. By not exerting additional pressure you maintain a safer
stronger grip on the power tool when it breaks through the material, as well as reducing
wear on the power tool which will extend the power tool's service life. Additional pressure
may also bend or twist the accessory or blade which may cause it to break and cause
injury. If the power tool allows for being held with one or two hands hold with two hands
whenever possible. ALWAYS exercise caution when handling this power tool.
r) Sawing, cutting and abrasive actions create heat. This may affect the workpiece and
power tool. ALWAYS monitor the heat level and in the event of excessive heat switch off the
power tool and allow to cool before restarting work. Some power tools depending on design
may be more quickly and effectively cooled by running at high speed without load.
s) The power tool will draw in dust through the vents on its body. Excessive accumulation
of powdered metal may cause an electrical hazard and destroy the tool. ALWAYS ensure the
environment dust level is safe for the tool and ensure the vents are not blocked.
t) For mains-operated power tools, ensure the cable of the power tool is ALWAYS kept
behind the tool and never close to where the accessory or blade is operating.
u) DO NOT reach under the workpiece, rest the workpiece on your body, or hold the
workpiece while working on it, as contact with the blade or accessory protruding
from the workpiece can result in serious injury.
v) Anti-vibration gloves should be worn when operating power tools that produce large
amount of vibration, especially during long-term use.
w) For power tools with a rotating mechanism and accessories ensure the operator is
not wearing clothes or gloves with frayed threads, cords etc. that could be entangled
in the rotating mechanism dragging the operator's hand into the rotating accessory
causing injury. ALWAYS wear tight fitting work clothes, safety shoes. Remove jewellery
and secure long hair. NEVER wear fabric-based gloves that can produce strands of material
when operating this type of power tool.
x) DO NOT allow sanding sheets to wear away on the sanding pad. This will damage the
surface of the pad requiring replacement and may cause parts of the sanding sheet to fly
off the pad, causing operator injury.
y) DO NOT touch the moving sanding sheet.
z) Wire brush bristles are thrown by the brush even during ordinary operation. DO NOT
overstress the wires by applying excessive load to the brush. The wire bristles can easily
penetrate light clothing and skin.

Product Familiarisation

1. Cutting/Sanding Accessory
2. Dust Extraction Collar
3. Dust Extraction Port
4. Keyless Change Lever
5. ON/OFF Switch
6. Grip
7. Variable Speed Dial
8. Motor Vents
9. Auxiliary Handle Hole
10. Auxiliary Handle
11. Work Light
12. Flange
13. Dust Collar Threaded Holes
14. Locking Knob

Intended Use

Oscillating multi-tool with quick tool change mechanism, designed for cutting and abrasive
tasks by fast oscillation of a blade, file or sanding pad.

Unpacking Your Tool

• Carefully unpack and inspect your tool. Fully familiarise yourself with all its features
and functions
• Ensure that all parts of the tool are present and in good condition. If any parts are missing
GB
or damaged, have such parts replaced before attempting to use this tool

Before Use

WARNING: Always ensure that the tool is switched OFF and unplugged from the power
supply before fitting or removing the Dust Extraction Collar or accessories.
WARNING: Always wear suitable gloves when handling blades or other sharp accessories.
WARNING: Accessories and tool may become hot during use. Always allow to cool before
removing or changing accessories.
6
Fitting the Dust Extraction Collar
Note: This Keyless Oscillating Multi-Tool is designed to be connected to a household vacuum
cleaner hose or workshop dust extraction system. This is the preferred and most effective
method of dust extraction.
WARNING: ALWAYS connect the Keyless Oscillating Multi-Tool to a suitable vacuum cleaner
or workshop dust extraction system if the sanding dust contains harmful substances, such
as particles from old paint, varnish, surface coatings, etc. ALWAYS dispose of harmful dust
according to laws and regulations.
1. Place the Dust Extraction Collar (2) over the Flange (12) so that the flat part of the collar
with the holes is against the multi-tool
2. Locate one of the holes on the collar and align it with one of the Dust Collar Threaded Holes
(13) (Image A) so Dust Extraction Port (3) is either on the left or right side of the multi-tool
3. Insert the Locking Knob (14) into the Dust Collar Threaded Hole and tighten to fasten the
Dust Extraction Collar
Note: The installation of the collar must be carried out without an accessory installed on the
multi-tool (see 'Fitting a blade or scraper' or 'Fitting the sanding pad & sanding sheets').
Note: The Dust Extraction Port is designed to fit a standard 32mm diameter hose. When
working in confined spaces, the Dust Extraction Port can be removed.
Fitting the Dust Extraction Port
1. With the hole facing up, push the Dust Extraction Port (3) onto the Dust Extraction Collar (2)
2. To remove, pull the Dust Extraction Port away from the Dust Extraction Collar
Fitting a vacuum hose
Note: The vacuum and hose is not supplied.
1. Push a compatible size vacuum or dust extraction system hose onto the Dust Extraction
Port (3)
2. If working in a confined space with no room for dust extraction, the Dust Extraction Port can
be removed while still attached to the hose, and will be ready for quick reattachment
Fitting a blade or scraper
1. Lift the Keyless Change Lever (4) and push forward then loosen the Flange (12) by rotating
the lever anti-clockwise
Notes:
• If the accessory is open ended, the Flange can be loosened partially to fit the accessory
(Fig. I & III)
• If the accessory has a closed end, the Flange will need to be loosened and removed from
the multi-tool to fit the accessory (Fig. II) before re-inserting the Flange. A small amount of
finger pressure on the Flange is necessary when first tightening
2. Align the accessory holes with the buttons on the Flange and tighten rotate the Keyless
Change Lever clockwise to tighten the Flange
3. Close the lever back down to the original position on the multi-tool
4. To remove, repeat steps 1–3 and remove the blade or scraper during step 2 (Fig. II)