Initial Start-Up; Initial Setup - Indexa AC20 Mode D'emploi

!
Do not connect any damaged device (e.g. damage in transit). Repairs to
the equipment must only be performed by specialists.
!
Remove the mains adapter from the mains outlet when the device is not
required for a longer time.
7. Location
Before mounting the camera check the wireless reception from the desired
location. Check the operation of the camera and the connection in the
proposed location.
Observe the following points:
!
Position the camera so that no direct light or sunshine falls on the lens
otherwise the picture may become overexposed. Check the camera image
before mounting. Provisionally connect and commission the device and
hold the camera in the desired position. If necessary, change the camera
position until you have found the desired view.
!
Select the distance between the camera and the subject according to the
level of detail desired.
!
The camera has infrared illumination for the close range. This is
activated by the daylight sensor. You can improve the quality of the
image at night by using additional illumination. The camera
automatically switches to black and white in low light conditions and in
artificial light.
!
Ensure that there is a possible cable routing at the installation location.
!
If you want to prevent unauthorised access to the camera or memory
card, please ensure that the camera is installed out of reach.
!
For night time viewing do not point the camera through window glass as
the infrared light will be reflected into the image.
!
When using WiFi:
#
Ensure that the camera has a good WiFi connection with the WiFi
router.
#
The maximum range of the WiFi is dependent on the environment
and on the WiFi router. The transmission range is reduced through
walls and floors (particularly those with steel reinforcement). Metal
surfaces eg. refridgereators, shelving vapour-coated glass surfaces or
mirrors will block the wireless transmission.
#
The WiFi transmission can also be affected by strong electric fields and
other wireless equipment. Ensure an adequate distance of the camera
and receiver to microwave ovens, cordless phones, mobile phones,
devices using the same or similar frequency, electric motors and high
voltage devices or power cables.
#
If the WLAN connection is poor, change the position of the camera or
the WLAN router or use a WLAN repeater.
8. Important notes on operating the camera
via the Internet
#
In order to access the registered camera via the Internet,
#
the WLAN router must be connected to the Internet and
#
the camera must be connected to the WLAN router (green connection
LED [6] is lit continuously when connected).
#
On the WLAN router, the encryption standard WPA/WPA2/WPA2-PSK and
34 - GB
the DHCP protocol must be activated, and the SSID must be public.
#
The camera identification number (SSID), which needs to be entered into
your mobile device, can be found on the label on the back of the camera.
#
Image and audio transmission are delayed (depending on the quality of
the connections). The worse the connection between the camera and WLAN
router, the worse the transmission may be.
#
Up to three users can simultaneously access the same camera.
#
Any number of cameras can be registered to one mobile device.
#
The app is occasionally updated and improved. As a result, there may be
deviations from the following details in certain circumstances.
Caution:
As with all mobile devices, substantial costs may be incurred when using an
Internet connection. It is therefore recommended to set up a suitable flatrate
plan.
9. Start-up

9.1 Initial start-up

For more information on how to first set up the camera and
how to first access it via the app, please also refer to the
enclosed quick-start guide.
To access the camera from a mobile device,
#
the mobile device must be connected directly to the camera once. In this
way, the data required to establish the connection from the camera to the
WLAN router can be entered.
Mobile
device
#
After the camera has been successfully connected to the WLAN router
(prerequisite: camera is in range of the WLAN router), you can access the
camera through this WLAN router via the app on the mobile devices (via
WLAN, provided the mobile device and camera are connected to the same
WLAN router, or via Internet).
Mobile
device
Mobile
device

Initial setup

Download app
!
Download the "OMGuard lite" app from the Play Store / App Store to your
mobile device (see QR code on the front page). If the iOS app is not found,
go to the App Store settings and select "iPhone only" rather than "iPad
only".
WLAN router
Internet