Publicité
RECIRCULATING
A
INSTALLATION OVERVIEW
A1. Attach Mounting Plate to Wall
A2. Prepare Top Cabinet
A3. Check Blower Orientation
A4. Adapting Microwave Blower For Recirculation
A5. Installing The Charcoal Filter
A6. Mount The Microwave Oven
A1
ATTACH THE MOUNTING PLATE TO
THE WALL
Attach the plate to the wall using toggle bolts and wood
screws . At least one wood screw must be used to
attach the plate to a wall stud .
Remove the toggle wings from the bolts .
1
Insert the bolts into the mounting plate through the
2
holes designated to go into drywall and reattach
the toggle wings to
To use toggle bolts:
Spacing for Toggles More
Than Wall Thickness
Toggle Wings
Mounting
Toggle
Plate
Bolt
Wall
1" = 2.5 cm; 1' = 0.3 m
40
Installation Instructions
(Non-Vented Ductless)
⁄
" onto each bolt.
3
4
Bolt End
3/8" TO EDGE
OPTION 2
STEP 1:
Installer uses bracket to make 2 marks. First
OPTION 1
12"
mark is made by using the stampled slot in bracket.
Second mark is made on the ouside edge of bracket.
NOTE: IT IS VERY IMPORTANT TO
READ AND FOLLOW THE DIRECTIONS
F. CUT OUT FOR HORIZONTAL
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
4"
OUTSIDE EXHAUST
Horizontal line
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
CUT HOLE THROUGH REAR WALL FOR EXHAUST ADAPTOR
Make a mark
STEP 4:
accurately.
even with
here,
Make a mark here, along
inside bottom of the
2. Locate and mark at least one stud on the left or
stamped
bottom of
stamped slot provided.
right side of the centerline.
slot
NOTE:
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
STEP 2:
Installer moves bracket to the other side of
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
same as STEP 1, just opposite side.
the cabinets and makes 2 more marks. Marks are the
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
NOTE::
D O NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Make a
inside bottom of the
Make a mark here, along
even with
mark here,
Darle vuelta a la hoja para consultar la
stamped slot provided
(same as Step 1).
stamped
bottom of
versión en Español.
slot
CAUTION - IF EXHAUST ADAPTOR IS POSITIONED OUTSIDE
RECOMMENDED DIMENSION, GREASE-LADEN AIR WILL
DISCHARGE INTO HOUSE STRUCTURE
NOTES:
30" MINIMUM WIDTH REQUIRED
- 13" Max Cabinet Depth
Locate and mark holes to align with holes in the
- 15" deep cabinets require additional steps using
mounting plate.
an additional installation kit: JX36BUMP
IMPORTANT:
REAR WALL TEMPLATE
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK THE LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
C
Trim the rear wall template along the dotted line.
A
C
D
B
IMPORTANT: Do NOT
remove the cardboard spacers
between the heat shield and
door
Place the mounting plate against the wall and
3
insert the toggle wings into the holes in the wall to
mount the plate .
CAUTION
fingers between the back of the mounting plate and
the wall.
Tighten all bolts. Pull the plate away from the wall
4
to help tighten the bolts .
A2
USE TOP CABINET TEMPLATE FOR
PREPARATION OF TOP CABINET
You need to drill holes for the top support screws and a
hole large enough for the power cord to fit through .
• Read the instructions on the TOP CABINET
TEMPLATE.
• Tape it underneath the top cabinet .
• Drill the holes, following the instructions on the TOP
CABINET TEMPLATE.
CAUTION
Be careful to avoid pinching
Wear safety goggles when drilling
holes in the cabinet bottom.
29-6379
Publicité
