Publicité
ENGLISH
Manual:
-
While paused, short press the
button to send the robot to the base for recharge.
-
When the robot vacuum cleaner is charging,
light lights up steady orange.
-
After recharge,
will stay on, and ring indicator light will light up steady white.
Note:
If the robot vacuum cleaner cannot find the self-emptying base, it will automatically return
to the starting position. Please manually place the robot vacuum cleaner back in the self-
emptying base for recharge.
Malfunction
If a malfunction occurs during operation, the robot vacuum cleaner ring indicator light or
the corresponding self-emptying base indicator light will rapidly flash orange and the robot
vacuum cleaner will beep. Please refer to the Troubleshooting section.
Note:
-
If the robot vacuum cleaner isn't in the self-emptying base and no action is performed for
10 minutes during a malfunction, the robot vacuum cleaner will automatically enter Sleep
mode.
-
If a malfunction occurs, the robot vacuum cleaner will return to the self-emptying base for
recharge, and cleaning will end.
Resetting to factory settings
If the robot vacuum cleaner does not respond to any button presses, first press the Reset
button to force it to switch off, then press the Power button to restart it. If it still malfunctions,
hold down the
and the
buttons simultaneously for 15 seconds: the robot vacuum
cleaner will be restored to factory default.
4. CLEANING AND MAINTENANCE
Warning
Be sure to remove the mixed tank before turning the robot vacuum cleaner upside down.
Dirt tank
1. Press the tank release tab downwards and remove the tank as shown in Figure 11.
2. Open the dirt-tank cover and pull up the filter module.
3. Dirt can be removed with a small brush or by shaking carefully against a hard surface for
dust to fall off. You can also use warm water without detergents to get a better result. Fig.
12
66
slowly flashes white, and the ring indicator
4. If you wish to wash the filter, make sure it is completely dry before refitting it to prevent
moisture from getting into the motor and damaging the robot vacuum cleaner. Fig. 13
Note:
It is recommended to replace the filter every 3-6 months.
5. Open the filter cover, empty the inside, and rinse it repeatedly. If dirt is present, wipe the
dirt container with a dry cloth and refit the assembly. Fig. 14
Note:
-
Do not use sharp objects to clean the surface of the tank.
Wash it with clean water without adding detergent.
-
Omnidirectional wheel
1. Remove the mixed tank from the robot vacuum cleaner and turn it upside down. Use tools
such as a small screwdriver to pry the axle and remove the wheel as shown in Figure 15.
Note: do not remove the omnidirectional-wheel bracket.
2. Remove hair or dirt from the wheel and axle. Fig. 16
3. If you decide to use water to clean the wheel, make sure it's dry before refitting it.
4. Refit the wheel and securely tighten it.
Side brush
1. Remove the mixed tank from the robot vacuum cleaner and turn it upside down.
2. Pull the side brush out as shown in Figure 17 to remove it.
3. Clean the side brush and refit it in position.
Note:
It is recommended to replace the side brush every 3-6 months.
Main brush
1. Remove the mixed tank from the robot vacuum cleaner and turn it upside down.
2. Slightly press the main-brush frame's tabs to open the main-brush compartment and
remove it as shown in Figure 18.
3. Pull the mop roller upwards and clean the main-brush frame.
4. Use the self-cleaning brush to remove hair tangled on the main brush as shown in Figure
19.
5. Refit the main brush, firmly press down the brush frame, and secure the clip.
Note:
Weekly cleaning is recommended.
-
-
It is recommended to clean the main brush with a damp cloth. If you decide to use water to
clean it make sure it's dry before refitting it.
ENGLISH
67
CONGA 14090 TWICE ROLLER HOME&FILL
Publicité
