Publicité
ENGLISH
-
If the self-emptying base malfunctions, the indicator lights light up orange. For specific
troubleshooting methods, please refer to the Troubleshooting section.
-
Do not use the self-emptying base without the water tank, dirt-disposal bag, etc. installed.
Be sure to place the water tank inside the self-emptying base. The self-emptying base has
a factory-fitted dirt-disposal bag.
-
Self-emptying bases undergo a water test before leaving the factory. It is normal for a
small amount of water to remain in the water tank.
Do not expose the self-emptying base to direct sunlight or block the infrared sensors with
-
any objects, otherwise the robot vacuum cleaner may not be able to automatically return
to the base.
Filling up the water tank
1. Open the top cover of the self-emptying base and remove the water tank.
2. Open the top cover of the water tank and fill it up. Do not fill up the water tank above the
MAX mark and below the MIN mark. Fig. 8
3. After adding water, close the top cover and secure the water tank release tab.
4. Refit the water tank in the self-emptying base and press down the top cover to secure it
in place.
Note:
-
Do not add hot water to the water tank to avoid deformation of the tank.
-
If you notice water stains on the outside of the water tank, wipe them with a soft, dry cloth
before use.
3. OPERATION
Charging and switching the robot vacuum cleaner on
1. Place the robot vacuum cleaner on the floor, with the rear facing the self-emptying base,
then centre it.
2. Push the robot vacuum cleaner all the way to the back of the base. Make sure the guide
wheel of the robot vacuum cleaner's dirt tank fits into the alignment guide of the self-
emptying base, and that the robot vacuum cleaner is recharging. The robot vacuum
cleaner will automatically start recharging once its charging terminals touch the charging
terminals of the self-emptying base. After about 5 seconds, the light of the robot vacuum
cleaner will turn on accompanied by an acoustic signal, indicating proper switch-on.
-
If the robot vacuum cleaner leaves the self-emptying base, hold down
light turns steady white and manually place the robot vacuum cleaner in the self-emptying
base for charge following the steps above.
Note:
If the battery is low, it may not be possible to switch the robot vacuum cleaner on. Manually
-
62
-
Pairing the self-emptying base to the robot vacuum cleaner
1. After switching the robot vacuum cleaner on and placing it in the self-emptying base,
2. Once the robot vacuum cleaner has been successfully paired with the self-emptying base
Note:
If you replace the robot vacuum cleaner for after-sales maintenance or other reasons, unpair
it from the self-emptying base first.
Unpairing the robot vacuum cleaner from the self-emptying base
1. Unplug the self-emptying base from the power supply: the robot vacuum cleaner will
2. After switching the self-emptying base back on, switch on the new robot vacuum cleaner
3. After pairing, the Bluetooth indicator light on the self-emptying base turns from orange
Smartphone App
1. To use all available functions, it is recommended to control the robot vacuum cleaner via
2. Before you start, make sure your smartphone is connected to a working Wi-Fi network.
3. Turn the self-emptying base on: the robot vacuum cleaner will start charging. Once the
4. Enter the Wi-Fi password on the smartphone app, tap on 'Next', and follow the instructions
until the indicator
Note:
-
take the robot vacuum cleaner to the self-emptying base. During recharge, the
and the indicator light ring will light up orange.
The robot vacuum cleaner is equipped with a rechargeable high-performance lithium-ion
battery. To maintain battery performance, keep the robot vacuum cleaner charged for daily
use.
the Bluetooth indicator light will change from orange to white, signalling that Bluetooth
pairing between the base and the robot vacuum cleaner has been successful.
for the first time, the base will be linked to the robot vacuum cleaner, and the latter will
only be able to communicate with the paired base.
automatically be unpaired from the base.
and place it in the base: both will automatically start Bluetooth pairing.
to white, indicating that Bluetooth pairing between the self-emptying base and the robot
vacuum cleaner has been successful.
the dedicated app.
robot vacuum cleaner is charged, hold down (≥ 3s) the
light will light up white and flash slowly, indicating that the robot vacuum cleaner is trying
to connect to the Wi-Fi.
shown on the app.
Due to the improvement and update of the app, operation may differ slightly from the
above description. Follow the instructions shown on the app.
ENGLISH
button
button: the ring indicator
63
CONGA 14090 TWICE ROLLER HOME&FILL
Publicité
