Publicité
- Press the "SPEED +/-" buttons to set the speed. Press the
"INCLINE +/-" buttons to set the incline. Press the "MODE"
button to confirm.
The main display shows "SE02"
- Repeat the above action to configure the other steps.
- Press the "START" button to start the program.
Body Fat
The Body Fat program is program to indicate your fiscal state, based
on your body parameters and heart rate.
- Press "MODE" button to open programming mode.
- Press "PROG" buttons to select "8-1"
program, press "MODE" button to confirm.
- The "Distance" display shows "F1" (SEX) .
The "Calories" display shows "1"
Press "SPEED +/-" buttons to select:
1: Male/ 2: Female press "MODE" button to confirm.
- The "Distance" display shows "F2" (Age) .
The "Calories" display shows "25"
Press "SPEED +/-" buttons to select:10~99
press "MODE" button to confirm.
- The "Distance" display shows "F3" (Heigth) .
The "Calories" display shows "170"cm
Press "SPEED +/-" buttons to select:100~220 cm
press "MODE" button to confirm.
- The "Distance" display shows "F4" (Weigth) .
The "Calories" display shows "70"kg
Press "SPEED +/-" buttons to select: 20~150 kg
press "MODE" button to confirm.
- The "Distance" display shows "F5" (Active)
The "Calories" display shows "- - - -" (Measure)
CAUTION
• Holding the contact hand-grip heart rate measurement pads is
required for this function.
Result calculation:
- BODY TYPE: ( Body Fat ratio; 9 types)
• FAT 0 ~17
Underweight
• FAT 18 ~ 27
Standard
• FAT 28 ~ up
Overweight
- BF = Body Fat ( in ratio % )
- Error code "ER" will show if no heart rate was detected during the
BF measurement process.
- Press "MODE" button to leave Body Fat program.
ERP Function
ERP function can shut your treadmill in sleep mode automatically
when being without operation for 4:30 minutes.
You can turn this function On and off by:
- When treadmill is in "start up mode" press and hold "Mode"
button for 3 seconds to switch between On and Off mode.
• Display shows "1111" indicates On mode.
Machine will turn to sleep mode after 4:30 minutes being idle.
• Display shows "2222" indicates Off mode.
Machine will not turn into sleep mode after 4:30 minutes being
idle.
CAUTION
• We recommend to set ERP function in On mode always.
Cleaning and maintenance
WARNING
• Your trainer requires monthly maintenance, even when not being
used.
• Before cleaning and maintenance, remove the mains plug from
the wall socket.
• Do not use solvents to clean the equipment.
- Do not block the ventilation openings. Keep the ventilation
openings clear from dust, dirt and other obstructions.
- Clean the equipment with a soft, absorbent cloth after each use.
- Clean the visible parts of the equipment with a vacuum cleaner
with a small suction nozzle
- Regularly check that all screws and nuts are tight.
CAUTION
• We recommend to use indoor shoes only on your treadmill.
When you don't have these we do recommend to check the
soles of your footwear before using them on your treadmill.
The treadmill is not sustainable for dirt from outdoors.
General Cleaning
Dirt, dust, and pet hair can block air inlets and accumulate on the
running belt. On a monthly basis: vacuum underneath your treadmill
to prevent build-up.
UNPLUG POWER CORD BEFORE THIS TASK.
Belt Dust
This occurs during normal break-in or until the belt stabilizes. Wiping
off excess dust with a damp cloth will minimize build-up.
Belt and Running Deck
Your treadmill uses a very high-efficient low-friction bed.
Performance is maximized when the running deck is kept clean and
free from dust and dirt. Dirt and dust particles between running deck
and running belt will damage your running deck surface affecting
your performance and product lifetime.
How to clean running deck
Use a soft, dry, non-abrasive cloth to wipe the edge of the belt and
the area between the belt edge and frame. try to reach under the
running belt edges too, to remove the dirt build up on the edges too.
How to clean running belt surface
Firstly use a nylon scrub brush to remove the loose particles from the
running belt surface. Than use wrung out damp cloth (no cleaners or
abrasives) to gentle clean the top of the textured belt. Allow the belt
to fully dry before using.
NOTE
• When your belt too dirty to clean with water only, you can use a
mild soap, but never a lubricant solvent.
• Prevent that the solution comes between running deck and
running belt at all times.
This should be done on a regular basis to extend belt and running
deck life.
2 1
English
Publicité
