Publicité
Liens rapides
Page 1 of 11
LP0374BK
FITTING INSTRUCTIONS FOR LP0374BK
LICENCE PLATE BRACKET
This kit contains the items pictured and labelled over page.
Some parts may be shown for clarity of instructions only.
Do not proceed until you are sure all parts are present.
Please read all instructions before proceeding.
IF IN ANY DOUBT WHEN FITTING OUR PRODUCTS, CONSULT ONE OF OUR DEALERS
OR HAVE FITTED BY A QUALIFIED TECHNICIAN.
Please note that the way the kit is packed does not necessarily represent the way of
mounting to the bike.
In the event of rubber washers being used to hold components onto bolts,
these rubber washers can be thrown away.
R&G
Unit
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
Tel: +44 (0)
420 89007 www.rg-racing.com Email: info@rg-racing.com
1
Publicité
Manuels Connexes pour R&G LP0374BK
Sommaire des Matières pour R&G LP0374BK
- Page 1 Page 1 of 11 LP0374BK FITTING INSTRUCTIONS FOR LP0374BK LICENCE PLATE BRACKET This kit contains the items pictured and labelled over page. Some parts may be shown for clarity of instructions only. Do not proceed until you are sure all parts are present.
- Page 2 Page 2 of 11 LP0374BK TOOLS REQUIRED GENERAL TORQUE SETTINGS Set of metric Hex keys to include M4 BOLT = 8Nm • 5mm & 6mm. M5 BOLT = Set of metric sockets and wrench. • To include 8mm, 10mm & 12mm.
- Page 3 Page 3 of 11 LP0374BK 1390 ASSEMBLY DIAGRAM 990 ASSEMBLY DIAGRAM R&G Unit , Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0) 420 89007 www.rg-racing.com Email: info@rg-racing.com...
- Page 4 Page 4 of 11 LP0374BK FITTING PICTURES FITTING INSTRUCTIONS Disassembly of OEM Tail Unit: Disconnect the wiring connectors going to the OEM Tail Unit located under the passenger seat. Remove the OEM tail unit via the four bolts underneath the passenger seat.
- Page 5 Page 5 of 11 LP0374BK Then fit the remaining washers to the 2x M6 bolts and pass through the cover plate, mounting bracket and into the undertray. Please see the fitting Pictures for reference. Then fully tighten the bolts to the required torque spec.
- Page 6 The customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods. NOTICE DE MONTAGE LP0374BK SUPPORT DE PLAQUE...
- Page 7 Page 7 of 11 LP0374BK SI DES RONDELLES EN CAOUTCHOUC SONT UTILISEES POUR MAINTENIR LES COMPOSANTS SUR LES BOULONS ELLES PEUVENT ETRE JETEES OUTILS REQUIS VALEURS DE SERRAGE Clés Allen 5 & 6mm. • M4 BOULON = 8Nm Clé à cliquet + douilles 8mm, •...
- Page 8 Page 8 of 11 LP0374BK 1390 SCHÉMA D’ENSEMBLE 990 SCHÉMA D’ENSEMBLE R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 9 Page 9 of 11 LP0374BK PHOTOS DE MONTAGE NOTICE DE MONTAGE Démontage de l'unité d’origine : Débranchez les connecteurs de câblage allant à l'unité arrière d’origine située sous le siège passager. Retirez l'unité arrière d’origine via les quatre boulons sous le siège passager.
- Page 10 Page 10 of 11 LP0374BK Présentez la plaque de recouvrement (article 3) à l'assemblage, en veillant à ne pas pincer/capturer le sous-faisceau et passez les 2 boulons à tête fraisée restants à travers la plaque d'immatriculation et les supports de montage principaux, puis appliquez les rondelles et les écrous sur le filetage exposé...
- Page 11 Page 11 of 11 LP0374BK The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained otherwise than in accordance with R&G’s or manufacturer’s instructions and good engineering practice or if the defect arises...