Publicité
9.1.e - Storing the machine (Fig. 19)
NOTE:
Before storing the machine, ensure that the
tanks (12) and (13) are empty.
The machine was designed to be stored in
confi ned spaces.
-
Lower the handle bar (1), the machine
can be placed under a shelf or it can be
lifted vertically according to the drawing
in order to be placed between two furniture
pieces.
10.1 DRAINING THE
RECOVERY WATER (Fig.20)
At the end of the washing cycle or when the
recovery water tank (13) is full, it is necessary
to empty the tank by proceeding as follows:
NOTE:
To dispose of the recovery water, comply
with the standards in force in the country in
which the machine is used.
-
Lift the lid (11).
-
Remove the tank (13) by lifting the machine
using the handle bars (43).
-
Place it on an drain valve and fully drain
the entire water from the tank.
-
Clean the gasket (44) with a wet cloth.
-
Clean the inside of the tank and replace it
on the machine, ensuring that the handle
bars (43) are withdrawn, as shown in the fi gure.
11.1 MAINTENANCE AND CLEANING
Warning
WARNING:
For information and warnings regarding
maintenance or cleaning, follow the information
given in the "General warnings
during maintenance" in chapter 1 in this manual.
OPERATIONS TO PERFORM DAILY
11.1.a - Emptying and cleaning the
clean water tank (Fig. 21)
Warning
WARNING:
At the end of the washing operations, it is
compulsory to drain and clean the clean
water tank to prevent deposits or scaling.
After draining the recovery water tank, drain
the clean water tank as follows:
-
Lift the lid (11 Fig. 1) and remove the tank (12).
-
Drain the water from a drain valve and
wash the tank inside with clean water;
also, clean well the fi lter (45).
-
Replace the tank.
11.1.b - Cleaning the recovery water tank (Fig. 20)
Warning
WARNING:
At the end of the washing operations, it
is compulsory to clean the recovery water
tank to prevent deposits or scaling
and the proliferation of bacteria, odours or mould.
-
Drain and clean the recovery water as indicated
in the corresponding paragraph.
-
Replace all the components in reverse order.
11.1.c - Removal of the squeegee system (Fig. 22)
-
Remove the tank (13 Fig. 1) as indicated
in the corresponding paragraph.
-
Release the lever (8).
-
Pull the lever (14) and lift the arm at the
same time (45).
-
Disconnect the two vacuum tubes (46)
from the corresponding holder.
-
Pull out towards the outside of the squeegee
system (47).
To replace, perform the steps in reverse order ensuring
the correct position of the two tubes (46) in the
corresponding housings.
11.1.d - Cleaning the squeegee system (Fig. 23)
In order to clean the squeegee correctly (48),
it is necessary to remove it as follows:
-
Remove the group as indicated in the
corresponding paragraph.
-
Turn the levers (49) towards the outside
and place them on both sides of the
group.
-
Remove the wipers (48) on both sides.
Wash properly the wipers (48), the vacuum
blocks (50), the inside of the body
(51) and the wheels (52), verify that the
tubes (46) are not obstructed by cleaning
them well on their upper part.
NOTE:
If during the washing, you notice that the
rubber blades (53) are damaged or worn, it
is necessary to replace them or to turn them upside down.
-
Replace all the components in reverseorder.
11.1.e - Cleaning the brush (Fig. 24)
Warning
WARNING:
Do not put the brush into a bucket or container
with water or water and detergent.
The brush can be removed both with the
squeegee system (48 Fig. 1) mounted or dismounted.
-
Press the button (55) from the central
part of the brush (9).
-
Slightly lift the machine and pull out the
brush (9) as shown in the fi gure.
-
Wash well the brush and check that there
are no wires or other fi bres on the brush.
-
Perform the steps in this section in reverse
EN
23
Publicité
