Publicité
EN
ease the dosage; the
inside of the lid features a graded scale
indicating the quantity of detergent in %
depending on the quantity of water in the tank.
-
Turn the lid (41) by placing it above the tank (12)
pouring the liquid detergent inside the tank.
-
Replace the tank on the machine.
NOTE:
Use only non-foaming detergents for fl oors,
for information on the quantity, please refer
to the instructions of the manufacturer of the
detergent and to the type of dirt (maximum
percentage to use: 3%).
Warning
DANGER:
If the detergent comes in contact with the
eyes and/or skin or if swallowed, refer to
the use and safety information booklet
provided by the manufacturer of the detergent.
9.1 OPERATION
9.1.a - Checks before use (Fig. 1)
-
Check that the tank (12), the tank (13)
and the lid (11) are placed correctly.
-
Check that the brush (9) is correctly attached.
-
Check that the tank (12) is fi lled in with
clean water and detergent (if necessary).
-
Check the correct position of the battery
and its charge status (for operation with
battery).
-
Check the correct position of the charger
and that the plug is correctly inserted in
the power outlet (for operation with the mains).
9.1.b - Preparing the machine and
choosing the cycle (Fig. 17)
-
Lower the brush and the wipers by pressing
the pedal (10 Fig. 1) by releasing it from its slot.
Work cycle
-
The machine can perform 4 working cycles:
Dry only cycle
-
Press the button (37) for three seconds,
the LED (32) turns on, enabling the operation
of the vacuum cleaner, then press
the levers (4) or the lever (3) to start the cycle.
Brushing only cycle
-
In order to perform the brushing cycle
only, cut off the water supply by pressing
the button (36) and enable the operation
of the vacuum cleaner by pressing the
button (37), then press the levers (4) or
the lever (3) to start the cycle.
Washing, brushing cycle
-
In order to perform the washing and
brushing cycle, it is necessary to turn off
the vacuum cleaner by pressing the button
22
(37), then press the levers (4) or the
lever (3) to start the cycle.
Washing, brushing, drying cycle
-
Check that the vacuum cleaner and the
water supply are set up for the desired
function, then press the levers (4) or the
lever (3) to start the cycle.
9.1.c - Using the machine (Fig. 18)
-
After turning on the machine and choosing
the type of cycle, initiate the cleaning
operations by pressing and holding the
levers (4) or the lever (3); then turn off
the machine using the buttons (42) on the
handle bar (1).
NOTE:
By releasing the levers (4) or the lever (3),
the brush stops revolving and the water supply
is cut off , while the vacuum cleaner will
operate for another 10 seconds.
NOTE:
In order not to damage the fl oor and to avoid
excessive water accumulations, do not use
the machine stopped with the revolving
brush attached.
-
If needed, adjust the quantity of washing
water using the button (36).
-
Check the battery charge status by means
of the LEDs (34) (battery version only).
-
If needed, adjust the ground pressure of
the brush by pressing the button (15).
9.1.d - End of use and switching off (Fig. 18)
-
At the end of the cleaning operations,
before turning off the machine, cut off
the water supply by pressing the relative
button, continue with the vacuum cleaner
and with the revolving brush attached in
order to vacuum the entire liquid from the
fl oor and from the brush, then release the
levers (4).
-
Lift the brush assembly (9) by pressing
the pedal (10) until reaching the limit
switch securing it in the adequate slot.
Warning
WARNING:
Always lift the brush assembly at the end
of the cleaning operations in order to
avoid its deformation and of the rubber
blades.
-
Press the button (30), the LED (31) turns off .
-
Disconnect the power supply cord from
the socket (charger version only).
Publicité
