Publicité
1.1 INTRODUCTION
Warning
HAZARD:
Before using the machine, carefully read the
attached "SAFETY WARNINGS FOR THE
FLOOR SCRUBBER DRYER" manual.
2.1 GETTING TO KNOW
THE MACHINE (Fig. 1)
1)
Guide handle.
2)
Control panel.
3)
Handle adjustment, brush rotation and
water supply lever.
4)
Brush rotation and water supply lever.
5)
Battery release selector.
6)
Battery.
7)
Revolving wheels.
8)
Squeegee system arm release lever.
9)
Revolving brush.
10)
Brush and wiper lifting/lowering pedal.
11)
Tank lid.
12)
Clean water tank.
13)
Recovery water tank.
14)
Squeegee system release lever.
15)
Ground brush pressure adjustment selector.
16)
Cover latch.
48)
Squeegee system.
3.1 UNPACKING (Fig. 2)
After removing the package, check the integrity
of the machine and of all its components.
If any evident damage is found, contact the
area agent and the carrier within 3 days of receipt.
-
Remove the box (17) containing the accessories
and the bag (18) containing the brush.
3.1.a -
Machine equipment (battery version) (Fig. 3)
The accessories supplied are as follows:
6)
Battery.
9)
Brush.
19)
Machine use and maintenance manual.
20)
Battery charger instruction manual.
21)
Charger.
3.1.b -
Machine equipment (Fig. 4) (charger version)
19)
User and maintenance manual of the machine.
22)
Charger.
23)
Power supply cord.
3.1.c -
Car battery charger (optional) (Fig. 4a)
If needed, a car battery charger can be provided
to allow the cleaning machine battery charging on the
route. 35) Car battery charger (optional).
3.1.d - Machine lifting (Fig. 5)
NOTE:
Ensure that the lid (11) is well closed.
One person can lift the machine by inserting
a hand under the recovery tank "A" and the
other hand in the back of the machine under
the base "B"; please see fi gure.
4.1 ASSEMBLING THE COMPONENTS
4.1.a -
Mounting the brush (Fig. 6)
-
Lift the machine on vertically as shown in
the fi gure.
-
Insert the brush (9) by inserting it in the
axle (24), then turn it until it is secured in
the holder (25) and a "click" is heard.
-
Reposition the machine on the ground.
Warning
WARNING:
Use only brushes provided by the manufacturer
according to the model of the machine.
Using other types of brushes may compromise
the safety of the machine.
4.1.b -
Positioning of the handle (Fig.7)
-
Unlock the handle (1) pulling the lever (3)
and lift it placing it in the desired position.
4.1.c -
Battery mounting for the battery
version only (Fig. 8a)
-
Insert the battery (6) in the socket (26)
completely and then turn it towards the
machine until a click is heard.
4.1.d -
Charger mounting for the electric
version only (Fig. 8)
-
Check if the power supply cable (23) is
correctly inserted in the charger (22).
-
Insert the charger (22) in the socket (26)
completely and then turn it towards the
machine until a click is heard.
Warning
WARNING:
-
Make sure that the mains system is
equipped with an RCD (circuit breaker).
-
Unwind the electric power cable completely
before connecting it to the mains socket.
-
Use an electrical extension lead only
if in perfect condition; ensure that the
section is appropriate for the appliance
power rating.
-
Never let the power cable run over
sharp edges and do not tread on it.
-
The socket must be easily accessible.
5.1 CHARGING THE BATTERY (Fig. 9)
(IF EQUIPPED)
Warning
DANGER:
Charge the batteries in well-ventilated areas
which comply with standards in force
in the country of use. For safety-related information, follow
what is described in chapter 1 of this manual.
Warning
WARNING:
For information and warnings on the battery
charger, please refer to the manual of
the battery charger enclosed herein.
EN
19
Publicité
