Publicité
DIVA UTOPIA
U s e r m a n u a l
31 31
The loudspeakers are paired automatically when they are powered on.
During a factory reset, speaker pairing may not be automatic.
Here is the procedure to follow:
• Unplug all other nearby DIVA UTOPIA loudspeakers to avoid incorrect pairing.
• Connect the DIVA UTOPIA Primary and Secondary loudspeakers to the mains.
• The LED below the Speaker Pairing button on the Primary loudspeaker should be off, indicating
that the Secondary speaker is missing.
• Lightly press the pairing button on the Primary loudspeaker.
• The LED indicator on the loudspeaker will flash purple.
• Lightly press the pairing button on the Secondary loudspeaker.
• The LED indicator on the loudspeaker will flash purple.
• After a few seconds, the LEDs on the two pairing buttons on both loudspeakers should remain lit in white.
• The DIVA UTOPIA loudspeakers are paired.
If the pairing problem persists:
• Check that the two loudspeakers are not spaced more than 8m apart.
• Check that the loudspeakers are powered on.
• Check that the correct DIVA UTOPIA are paired.
• Check that there is no obstacle between the two loudspeakers, such as a wall, or any other object that could prevent a good
connection.
Wireless pairing provides speaker-to-speaker connection at up to 96kHz 24bit.
However, to enjoy the DIVA UTOPIA loudspeakers with a quality of 192kHz, using the RJ45 cable supplied in the accessory
box is recommended:
• Unpack the cable.
• Connect the Primary loudspeaker via the RJ45 port identified on the back of the PRIMARY DIVA UTOPIA as "Speaker Link".
• Connect the Secondary speaker via the RJ45 port identified on the back of the SECONDARY DIVA UTOPIA as "Speaker
Link".
Using the cable is required:
- To upgrade the resolution to 192kHz/24bit (wireless: 96kHz/24bit).
- Due to sound loss caused by interference.
Configuration with the Focal & Naim app (fig. 22)
In order to play streamed audio files and internet radio stations, DIVA UTOPIA loudspeakers must be connected to the internet
via a local network router. Connection to the router may be wired or wireless.
Note: The DIVA UTOPIA loudspeaker is configured by default to obtain its IP address using DHCP. DIVA UTOPIA can be confi-
gued to use a fixed IP address via is internal web setup pages.
Note: If the DIVA UTOPIA loudspeaker has been previously used it is good practice to return it to its default settings before
attempting to connecting it to the network. The factory default procedure will erase any existing user and network settings
and restore the default Radio presets. To do this, use the pin provided and insert it into the pinhole located in the "status"
section at the back of the DIVA UTOPIA.
In order for DIVA UTOPIA loudspeakers to connect to the internet via a local wireless network, they must be configured with
the wireless network name (SSID) and password (security key).
Note: The DIVA UTOPIA loudspeaker is Wi-Fi6 compatible.
Note: DIVA UTOPIA cannot connect to a "hidden" Wi-Fi network.
Wireless configuration with the Focal & Naim app
The Focal & Naim app incorporates a wireless setup routine that will guide you through the process of connecting DIVA UTO-
PIA loudspeakers wirelessly to your local network.
Scan the QR code to download and install the app (fig. 22).
Follow the steps below to implement the Focal & Naim app wireless setup routine.
• Make sure that the iOS or Android device the Focal & Naim app is installed on is connected to the same wireless network
used by the DIVA UTOPIA loudspeakers.
• Open the Focal & Naim app and select New Device Setup.
• Follow the on-screen instructions to connect the DIVA UTOPIA loudspeakers to the wireless network.
Wifi Reset & Factory Reset
Network Reset: Briefly press the reset button (through the pinhole) on the rear panel of the primary speaker using the tool
provided (fig. 7 - K).
Factory Reset: Press the reset button (through the pinhole) on the rear panel of the primary speaker for 3 seconds using the
tool provided (fig. 7 - K).
Publicité
