Publicité
In the case of right bevel cut
(a) (b)
1
1. Inside corner 2. Outside corner
Table (A)
–
Molding
Bevel angle
position
52/38°
in the
type
¿JXUH
For
D
Right
inside
33.9°
corner
E
For
F
outside
G
corner
Table (B)
–
Molding
position in
WKH ¿JXUH
For inside
D
corner
E
For outside
F
corner
G
Example:
In the case of cutting 52/38° type crown molding for
SRVLWLRQ D LQ WKH DERYH ¿JXUH
•
Tilt and secure bevel angle setting to 33.9° RIGHT.
‡
$GMXVW DQG VHFXUH PLWHU DQJOH VHWWLQJ WR ƒ
RIGHT.
‡
/D\ FURZQ PROGLQJ ZLWK LWV EURDG EDFN KLGGHQ
surface down on the turn base with its WALL
CONTACT EDGE against the guide fence on the
saw.
‡
7KH ¿QLVKHG SLHFH WR EH XVHG ZLOO DOZD\V EH RQ
the RIGHT side of the blade after the cut has been
made.
(c) (d)
2
Miter angle
45° type
52/38°
45° type
type
Right
Right
Right
30°
31.6°
35.3°
Left
Left
31.6°
35.3°
Right
Right
31.6°
35.3°
Molding
Finished
edge against
piece
guide fence
Wall contact
Finished
edge should
piece will be
be against
on the Right
guide fence.
side of blade.
Ceiling
contact edge
Finished
should be
piece will be
against guide
on the Left
fence.
side of blade.
Wall contact
edge should
be against
guide fence.
Crown molding stopper
Optional accessory
Crown molding stoppers allow easier cuts of crown
molding without tilting the saw blade. Install them on the
WXUQ EDVH DV VKRZQ LQ WKH ¿JXUHV
At right 45° miter angle
Fig.56: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
At left 45° miter angle
Fig.57: 1. Crown molding stopper L 2. Crown mold-
ing stopper R 3. Turn base 4. Guide fence
Position crown molding with its WALL CONTACT EDGE
against the guide fence and its CEILING CONTACT EDGE
DJDLQVW WKH FURZQ PROGLQJ VWRSSHUV DV VKRZQ LQ WKH ¿JXUH
$GMXVW WKH FURZQ PROGLQJ VWRSSHUV DFFRUGLQJ WR WKH VL]H RI
the crown molding. Tighten the screws to secure the crown
PROGLQJ VWRSSHUV 5HIHU WR WKH WDEOH & IRU WKH PLWHU DQJOH
Fig.58: 1. Guide fence 2. Crown molding stopper
1. Inside corner 2. Outside corner
Table (C)
–
Molding
position in
WKH ¿JXUH
For inside
corner
For outside
corner
Cutting aluminum extrusion
Fig.59: 1. Vise 2. Spacer block 3. Guide fence
4. Aluminum extrusion 5. Spacer block
When securing aluminum extrusions, use spacer blocks or pieces
RI VFUDS DV VKRZQ LQ WKH ¿JXUH WR SUHYHQW GHIRUPDWLRQ RI WKH DOX-
minum. Use a cutting lubricant when cutting the aluminum extru-
sion to prevent build-up of the aluminum material on the blade.
WARNING:
Never attempt to cut thick or
round aluminum extrusions. Thick or round alumi-
QXP H[WUXVLRQV FDQ EH GLI¿FXOW WR VHFXUH DQG WKH ZRUN
may loosen during the cutting operation which may
UHVXOW LQ ORVV RI FRQWURO DQG VHULRXV SHUVRQDO LQMXU\
32 ENGLISH
(a) (b)
(c) (d)
1
2
Miter angle
D
Right 45°
Save the right
side of blade
E
Left 45°
Save the left
side of blade
F
Save the right
side of blade
G
Right 45°
Save the left
side of blade
Finished
piece
Publicité
