Publicité
Automatic speed change function
Fig.12: 1. Mode indicator
Mode indicator status
On
This tool has "high speed mode" and "high torque
mode". It automatically changes operation mode
depending on the work load. When mode indicator
lights up during operation, the tool is in high torque
mode.
Blade guard
Fig.13: 1. Blade guard
When lowering the handle, the blade guard rises auto-
matically. The guard is spring loaded so it returns to
its original position when the cut is completed and the
handle is raised.
WARNING:
Never defeat or remove the blade
guard or the spring which attaches to the guard.
An exposed blade as a result of defeated guarding
PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\ GXULQJ RSHUDWLRQ
In the interest of your personal safety, always maintain
the blade guard in good condition. Any irregular opera-
tion of the blade guard should be corrected immediately.
Check to assure spring loaded return action of guard.
WARNING:
Never use the tool if the blade
guard or spring are damaged, faulty or removed.
Operation of the tool with a damaged, faulty or
UHPRYHG JXDUG PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
If the see-through blade guard becomes dirty, or saw-
dust adheres to it in such a way that the blade and/or
workpiece is no longer easily visible, remove the bat-
teries and clean the guard carefully with a damp cloth.
Do not use solvents or any petroleum-based cleaners
on the plastic guard because this may cause damage
to the guard.
If the blade guard is especially dirty and vision through
the guard is impaired, remove the batteries and use the
supplied wrench to loosen the hex bolt holding the cen-
ter cover. Loosen the hex bolt by turning it counterclock-
wise and raise the blade guard and center cover. With
the blade guard so positioned, cleaning can be more
FRPSOHWHO\ DQG HI¿FLHQWO\ DFFRPSOLVKHG :KHQ FOHDQLQJ
is complete, reverse procedure above and secure the
bolt. Do not remove spring holding blade guard. If guard
becomes discolored through age or UV light exposure,
contact a Makita service center for a new guard. DO
NOT DEFEAT OR REMOVE GUARD.
Fig.14: 1. Center cover 2. Hex wrench 3. Blade
guard
Operation mode
Off
High speed mode
High torque mode
Kerf boards
This tool is provided with the kerf boards in the turn base to
minimize tearing on the exit side of a cut. The kerf boards are
IDFWRU\ DGMXVWHG VR WKDW WKH VDZ EODGH GRHV QRW FRQWDFW WKH
NHUI ERDUGV %HIRUH XVH DGMXVW WKH NHUI ERDUGV DV IROORZV
Fig.15: 1. Kerf board
Fig.16: 1. Left bevel cut 2. Straight cut 3. Right
bevel cut 4. Saw blade 5. Blade teeth
6. Kerf board
First, remove the batteries. Loosen all the screws (2
HDFK RQ OHIW DQG ULJKW VHFXULQJ WKH NHUI ERDUGV XQWLO WKH
kerf boards can still be easily moved by hand. Lower the
handle fully, then pull and turn the stopper pin to lock
the handle in the lowered position. Release the stopper
pin on the sliding pole and pull the carriage toward you
IXOO\ $GMXVW WKH NHUI ERDUGV VR WKDW WKH NHUI ERDUGV MXVW
contact the sides of the blade teeth. Tighten the front
VFUHZV GR QRW WLJKWHQ ¿UPO\ 3XVK WKH FDUULDJH WRZDUG
WKH JXLGH IHQFH IXOO\ DQG DGMXVW WKH NHUI ERDUGV VR WKDW
WKH NHUI ERDUGV MXVW FRQWDFW WKH VLGHV RI EODGH WHHWK
7LJKWHQ WKH UHDU VFUHZV GR QRW WLJKWHQ ¿UPO\
$IWHU DGMXVWLQJ WKH NHUI ERDUGV UHOHDVH WKH VWRSSHU SLQ DQG
raise the handle. Then tighten all the screws securely.
NOTICE:
After setting the bevel angle ensure
that the kerf boards are adjusted properly. Correct
DGMXVWPHQW RI WKH NHUI ERDUGV ZLOO KHOS SURYLGH SURSHU
support of the workpiece minimizing workpiece tear
out.
Maintaining maximum cutting capacity
7KLV WRRO LV IDFWRU\ DGMXVWHG WR SURYLGH WKH PD[LPXP
cutting capacity for a 305 mm saw blade.
When installing a new blade, always check the lower limit
SRVLWLRQ RI WKH EODGH DQG LI QHFHVVDU\ DGMXVW LW DV IROORZV
First, remove the batteries. Turn the stopper lever to
engaged position.
Fig.17: 1. Stopper lever
Push the carriage toward the guide fence fully and
lower the handle completely.
$GMXVW WKH EODGH SRVLWLRQ E\ WXUQLQJ WKH DGMXVWLQJ EROW
with the hex wrench. The periphery of the blade should
come to the point where the front face of the guide fence
meets the top surface of the turn base and also it should
extend slightly below the top surface of the turn base.
Fig.18: 1. $GMXVWLQJ EROW
Fig.19: 1. Top surface of turn base 2. Periphery of
blade 3. Guide fence
With the batteries removed, rotate the blade by hand
while holding the handle all the way down to be sure
that the blade does not contact any part of the lower
EDVH 5HDGMXVW VOLJKWO\ LI QHFHVVDU\
$IWHU DGMXVWPHQW DOZD\V UHWXUQ WKH VWRSSHU OHYHU WR WKH
original position.
WARNING:
After installing a new blade and
with the batteries removed, always be sure that
the blade does not contact any part of the lower
base when the handle is lowered completely. If
a blade makes contact with the base it may cause
NLFNEDFN DQG UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
25 ENGLISH
Publicité
