Publicité
Electronic function
Soft start feature
This function allows the smooth start-up of the tool by
limiting the start-up torque.
Laser beam action
CAUTION:
Never look into the laser beam.
'LUHFW ODVHU EHDP PD\ LQMXUH \RXU H\HV
7R WXUQ RQ WKH ODVHU EHDP SUHVV WKH XSSHU SRVLWLRQ ,
of the switch. To turn off the laser beam, press the lower
SRVLWLRQ RI WKH VZLWFK
Fig.30: 1. Switch for laser
Laser line can be shifted to either the left or right side of
WKH VDZ EODGH E\ WXUQLQJ WKH DGMXVWLQJ VFUHZ DV IROORZV
Fig.31: 1. $GMXVWLQJ VFUHZ
1.
/RRVHQ WKH DGMXVWLQJ VFUHZ E\ WXUQLQJ LW
counterclockwise.
2.
:LWK WKH DGMXVWLQJ VFUHZ ORRVHQHG VOLGH WKH
DGMXVWLQJ VFUHZ WR WKH ULJKW RU OHIW DV IDU DV LW JRHV
3.
7LJKWHQ WKH DGMXVWLQJ VFUHZ ¿UPO\ DW WKH SRVLWLRQ
where it stops sliding.
NOTE: /DVHU OLQH LV IDFWRU\ DGMXVWHG VR WKDW LW LV SRVL-
tioned within 1 mm from the side surface of the blade
FXWWLQJ SRVLWLRQ
NOTE: When laser line appears dim and hard to see
because of direct sunlight, relocate the work area to a
place where there is less direct sunlight.
Aligning the laser line
Align the cutting line on your workpiece with the laser
line.
Fig.32
$ :KHQ \RX ZDQW WR REWDLQ WKH FRUUHFW VL]H RQ WKH OHIW
side of workpiece, shift the laser line to the left of the
blade.
% :KHQ \RX ZDQW WR REWDLQ WKH FRUUHFW VL]H RQ WKH ULJKW
side of workpiece, shift the laser line to the right of the
blade.
NOTE: Use wood facing against the guide fence
when aligning the cutting line with the laser line at the
side of guide fence in compound cutting (bevel angle
ƒ DQG PLWHU DQJOH ULJKW ƒ
ASSEMBLY
WARNING:
Always be sure that the tool is
switched off and the battery cartridge is removed
before working on the tool. Failure to switch off and
remove the battery cartridge may result in serious
SHUVRQDO LQMXU\
Hex wrench storage
When not in use, store the hex wrench as shown in the
¿JXUH WR NHHS LW IURP EHLQJ ORVW
Fig.33: 1. Hex wrench
Removing and installing saw blade
WARNING:
Always be sure that the tool is
switched off and the battery cartridge is removed
before installing or removing the saw blade.
Accidental start up of the tool may result in serious
SHUVRQDO LQMXU\
WARNING:
Use only the Makita wrench pro-
vided to install or remove the saw blade. Failure to
use the wrench may result in overtightening or insuf-
¿FLHQW WLJKWHQLQJ RI WKH KH[ VRFNHW EROW DQG VHULRXV
SHUVRQDO LQMXU\
WARNING:
Never use or substitute the parts
which are not supplied with this tool. Using such
SDUWV FDQ FDXVH VHULRXV SHUVRQDO LQMXU\
WARNING:
After installing the saw blade,
always make sure that it is securely installed.
Loose attachment of the saw blade can cause serious
SHUVRQDO LQMXU\
Always lock the carriage with raised position when
removing and installing the saw blade. Pull the stopper
pin and rotate it 90° with the carriage raised.
Fig.34: 1. Unlocked position 2. Locked position
3. Stopper pin
Removing the saw blade
Loosen the hex bolt holding the center cover using the
hex wrench. Raise the blade guard and center cover.
Fig.35: 1. Center cover 2. Hex wrench 3. Blade
guard
Press the shaft lock to lock the spindle and use the hex
wrench to loosen the hex socket bolt. Then remove the
KH[ VRFNHW EROW RXWHU ÀDQJH DQG VDZ EODGH
Fig.36: 1. Shaft lock 2. Hex wrench 3. Hex socket
EROW OHIWKDQGHG 4. Loosen 5. Tighten
Installing the saw blade
Mount the saw blade carefully onto the spindle, making
sure that the direction of the arrow on the surface of the
blade matches the direction of the arrow on the blade
case.
Fig.37: 1. Arrow on the blade case 2. Arrow on the
blade
,QVWDOO WKH RXWHU ÀDQJH DQG KH[ VRFNHW EROW 7LJKWHQ WKH
hex socket bolt counterclockwise using the hex wrench
while pressing the shaft lock.
Fig.38: 1. Hex socket bolt 2. 2XWHU ÀDQJH 3. Saw
blade 4. ,QQHU ÀDQJH 5. Spindle 6. Ring
NOTICE:
,I WKH LQQHU ÀDQJH LV UHPRYHG EH VXUH
to install it on the spindle with its protrusion fac-
ing away from the blade. ,I WKH ÀDQJH LV LQVWDOOHG
LQFRUUHFWO\ WKH ÀDQJH ZLOO UXE DJDLQVW WKH PDFKLQH
Return the blade guard and center cover to its original
position. Then tighten the hex bolt clockwise to secure
the center cover. Unlock the stopper pin to release
carriage from the raised position. Lower the handle to
make sure that the blade guard moves properly. Make
sure shaft lock has released spindle before making cut.
27 ENGLISH
Publicité
