Publicité
Horizontal vise
Optional accessory
WARNING:
Always rotate the vise nut clock-
wise until the workpiece is properly secured. If the
workpiece is not properly, secured the material may
move during the cutting operation causing possible
damage to the saw blade, causing the material to be
thrown and loss of control resulting in serious per-
VRQDO LQMXU\
WARNING:
When cutting a thin workpiece,
such as base boards, against the fence, always
use the horizontal vise.
CAUTION:
When cutting the workpiece of the
thickness 20 mm or thinner, make sure to use a
spacer block to secure the workpiece.
The horizontal vise can be installed in two positions on
either the left or right side of the base. When performing
22.5° or greater miter cuts, install the horizontal vise on
the side opposite the direction in which the turn base is
to be turned.
Fig.47: 1. Vise plate 2. Vise nut 3. Vise knob
%\ ÀLSSLQJ WKH YLVH QXW FRXQWHUFORFNZLVH WKH YLVH LV
released, and rapidly moves in and out. To grip the
workpiece, push the vise knob forward until the vise
SODWH FRQWDFWV WKH ZRUNSLHFH DQG ÀLS WKH YLVH QXW FORFN-
wise. Then turn the vise knob clockwise to secure the
workpiece.
NOTE: The maximum width of workpiece which can
be secured by the horizontal vise is 228 mm.
Sub base
WARNING:
Always support a long workpiece
so it is level with the top surface of the turn base
for an accurate cut and to prevent dangerous loss
of tool control. Proper workpiece support will help
avoid blade pinch and possible kickback which may
UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
WARNING:
Before the cutting operation,
always be sure that the sub bases are secured by
the screws.
To hold long workpieces horizontally, sub bases are
provided on both sides of the tool. Loosen the screws
and extend the sub bases to the appropriate length for
holding the workpiece. Then tighten the screws.
Fig.48: 1. Sub base 2. Screw
:KHQ FXWWLQJ SODFH WKH ZRUNSLHFH ÀDW DJDLQVW WKH JXLGH
fence and the sub fence on the sub base.
Fig.49: 1. Guide fence 2. Sub fence 3. Sub base
OPERATION
This tool is intended to cut wood products. With appro-
priate Makita genuine saw blades, following materials
can also be sawed :
—
Aluminum products
Refer to our website or contact your local Makita dealer for the
correct circular saw blades to be used for the material to be cut.
WARNING:
Make sure the saw blade is not con-
tacting the workpiece, etc. before the switch is turned
on. Turning the tool on with the blade in contact with the
ZRUNSLHFH PD\ UHVXOW LQ NLFNEDFN DQG VHULRXV SHUVRQDO LQMXU\
WARNING:
After a cutting operation, do not
raise the saw blade until it has come to a complete
stop. The raising of a coasting blade may result in
VHULRXV SHUVRQDO LQMXU\ DQG GDPDJH WR WKH ZRUNSLHFH
WARNING:
Do not perform any adjustment
such as turning grip, knob, and levers on the tool
while the saw blade is rotating. $GMXVWPHQW ZKLOH WKH
EODGH LV URWDWLQJ PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
NOTICE:
Before use, be sure to unlock the stopper
pin and release the handle from the lowered position.
NOTICE:
Do not apply excessive pressure on the
handle when cutting. Too much force may result in
RYHUORDG RI WKH PRWRU DQGRU GHFUHDVHG FXWWLQJ HI¿-
ciency. Press down handle with only as much force as
QHFHVVDU\ IRU VPRRWK FXWWLQJ DQG ZLWKRXW VLJQL¿FDQW
decrease in blade speed.
NOTICE:
Gently press down the handle to per-
form the cut. If the handle is pressed down with force
or if lateral force is applied, the blade may vibrate and
OHDYH D PDUN VDZ PDUN LQ WKH ZRUNSLHFH DQG WKH
precision of the cut may be impaired.
NOTICE:
During a slide cut, gently push the carriage
toward the guide fence without stopping. If the carriage
movement is stopped during the cut, a mark will be left in
the workpiece and the precision of the cut will be impaired.
Press cutting
WARNING:
Always lock the sliding movement
of the carriage when performing a press cutting.
Cutting without lock may cause possible kickback
ZKLFK PD\ UHVXOW LQ VHULRXV SHUVRQDO LQMXU\
Workpieces up to 92 mm high and 183 mm wide can be
cut in the following manner.
Fig.50: 1. Stopper pin
1.
Push the carriage toward the guide fence until it
stops and lock it with the stopper pin.
2.
Secure the workpiece with the proper type of vise.
3.
Switch on the tool without the blade making any contact
and wait until the blade attains full speed before lowering.
4.
Gently lower the handle to the fully lowered posi-
tion to cut the workpiece.
5.
When the cut is completed, switch off the tool and
wait until the saw blade has come to a complete
stop before returning the blade to its fully elevated
position.
29 ENGLISH
Publicité
