Publicité
Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is a stationary machine that uses cutting
discs to cut metal materials with and against the grain, in
straight lines and at mitre angles up to 45°, without the use
of water.
Using diamond-tipped cutting discs is not permitted.
Product features
The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1)
On/off switch
(2)
Handle
Retracting blade guard
(3)
(4)
Spindle lock
a)
(5)
Cutting disc
(6)
Angle guide
(7)
Locking spindle
(8)
Quick release
(9)
Spindle handle
(10)
Mounting holes
(11)
Base plate
(12)
Locking screw for angle guide
(13)
Transport safety lock
(14)
Hex key
(15)
Transport handle
(16)
Protective guard
(17)
Spark guard plate
(18)
Tool spindle
(19)
Clamping flange
(20)
Hex socket screw with flange
a) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cut-off grinder
Article number
Rated power input
No-load speed
Base plate dimensions
length x width x height
Bosch Power Tools
Cut-off grinder
Weight according to EPTA-
Procedure 01:2014
Protection class
Dimensions of suitable cutting discs
Max. cutting disc diameter
Max. cutting disc thickness
Hole diameter
Permitted workpiece dimensions (maximum/minimum): (see "Per-
missible workpiece dimensions", page 19)
The appliance meets IEC 61000-3-11 requirements and is subject to
conditional connection. The appliance can lead to occasional voltage
fluctuations under unfavorable power conditions. The impedance of
this appliance is set as Z
that the connection point, with the impedance Z
pliance shall be plugged in meets the impedance requirement: Z
≥ Z
tual
network supplier or supply authority.
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Values can vary depending upon the product and are subject to ap-
plication and environmental conditions. For further information
www.bosch-professional.com/wac.
Noise information
Noise emission values determined according to
EN 62841-3-10.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 104 dB(A); sound power level
109 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
To estimate noise emissions accurately, the times when the
tool is switched off, or when it is running but not actually be-
ing used, should also be taken into account. This may signi-
ficantly reduce noise emissions over the total working
period.
Assembly
GCO 230
Avoid starting the power tool unintentionally. The
u
3 601 M56 0..
mains plug must not be connected to the power supply
during assembly or when carrying out any kind of
W
2300
work on the power tool.
–1
min
4100
mm 489 x 265 x 73
mm
mm
mm
= 0.095 Ω. The user must make sure,
actual
. If Z
is unknown, determine Z
max
max
max
1 609 92A 8VB | (07.11.2023)
English | 17
GCO 230
kg
13.5
/ II
355
3.3
25.4
, on which the ap-
max
ac-
in consultation with the
Publicité
