Publicité
Les langues disponibles
Les langues disponibles
Product duration
The duration and average economic life of the product. The value of duration
is strongly affected by the fatigue index of the manoeuvres performed by the
automation: i.e. the sum of all factors that contribute to wear of the product
(see Table 1).
The estimation of duration is made on the basis of the design calculations and
the test results performed on prototypes. In fact, as it is an estimate, it does not
represent any guarantee regarding the effective duration of the product.
To establish the probable duration of your automation, proceed as follows:
01. Calculate the fatigue index by adding the percentage values of the items
present in Table 1.
02. In Graph A of the value just found, trace a vertical line that crosses the
curve; from this point trace a horizontal line until the "manoeuvre cycles"
line is crossed. The value determined is the estimated duration of your
product.
Example of the duration calculation of an XFAB(...) gear motor.
Refer to Table 1 and Graph A:
1) - Panel length: 1.7 m
2) - Panel weight: 200 kg = fatigue index: 20%.
3) - Installation in windy areas = fatigue index: 15%.
4) - Does not have other elements of fatigue.
Total fatigue index = 35%
Estimated duration = 120.000 manoeuvre cycles
CE declaration of conformity and declaration
of incorporation for a "quasi-machine"
Declaration in accordance with Directives: 2014/30/UE (EMC);
2006/42/EC (MD) annex II, part B.
Note - The content of this declaration corresponds to the declaration made
in the official document filed in the offices of Nice S.p.a., and particularly the
latest version thereof available prior to the printing of this manual. The text
contained here has been adapted to meet editorial requirements. A copy of
the original declaration may be requested from Nice S.p.a. (TV) I.
Declaration number: 320/XFAB
Name of manufacturer: NICE S.p.A.
Address: Via Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) Italy.
Person authorized to provide technical documentation: NICE S.p.A. –
Via Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) Italy.
Product type: Underground 24Vd.c. electro-mechanical gear motor for
swing gates.
Model / Type: XFAB2024, XFAB2124
Accessories: No accessory.
The undersigned Roberto Griffa, as Chief Executive Officer, hereby declares
under his own responsibility that the products identified above comply with
the provisions of the following directives:
• DIRECTIVE 2014/30/UE OF THE EUROPEAN PARLIAMENT AND
COUNCIL of February 26 2014 concerning alignment of Member States'
legislation regarding electromagnetic compatibility (consolidated text),
according to the following harmonized standards: EN 61000-6-2:2005;
EN 61000-6-3:2007 + A1:2011.
The product also complies with the following directive in accordance with
the requirements for "quasi-machines":
• Directive 2006/42/EC OF THE EUROPEAN PARLIAMENT AND COUN-
CIL of May 17 2006 regarding machines and amending directive 95/16/
EC (consolidated text).
4 – English
Revision: 7
Language: EN
TABLE 1
Length of the panel
≥ 1.50
(m)
Weight of the panel
(kg)
≤ 100
0 %
101 ÷ 250
10 %
251 ÷ 300
20 %
301 ÷ 330
30 %
331 ÷ 400
40 %
Environmental temperature exceeding 40°C or below
0°C or humidity exceeding 80%
Blind panel
Installation in windy area
GRAPH A
200.000
150.000
100.000
80.000
50.000
0
0
10
20
– I declare that the pertinent technical documentation has been prepared
in accordance with Annex VII B to Directive 2006/42/EC and that the fol-
lowing essential requirements have been met: 1.1.1 - 1.1.2 - 1.1.3 - 1.2.1
-1.2.6 - 1.5.1 -1.5.2 - 1.5.5 - 1.5.6 - 1.5.7 - 1.5.8 - 1.5.10 - 1.5.11.
– The manufacturer agrees to send the national authorities pertinent infor-
mation on the "quasi-machine" in response to a motivated request with-
out affecting its intellectual property rights.
– If the "quasi-machine" is operated in a European country with an official
language other than the language used in this declaration, the importer
must associate a translation with this declaration.
– The "quasi-machine" must not be operated until the final machine in
which it is to be incorporated is declared to conform to the provisions of
Directive 2006/42/EC, if applicable to it.
The product also complies with the following standards: EN 60335-1:2002
+ A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008 + A14:2010 +
A15:2011; EN 60335-2-103:2003 + A11:2009.
The parts of the product which are subject to the following standards
comply with them: EN 13241-1:2003 + A1:2011; EN 12445:2002; EN
12453:2002; EN 12978:2003 + A1:2009.
Oderzo, April 21 2016
1.51 ÷ 1.80 1.81 ÷ 2.00
2.01 ÷ 2.30
Fatigue index
10 %
20 %
20 %
30 %
30 %
40 %
40 %
50 %
50 %
–
30
40
50
60
70
80
90 100
fatigue index %
Eng. Roberto Griffa
(Chief Executive Officer)
30 %
40 %
50 %
–
–
15 %
15 %
15 %
Publicité
