MIRKA ROS525DBS Notice D'utilisation page 4

Please Read and Comply with
1) General Industry Safety & Health Regulations, Part 1910,
OSHA 2206, available from: Superintendent of Documents;
Government Printing Office; Washington DC 20402
2) Safety Code for Portable Air Tools, ANSI B186.1 available from:
American National Standards Institute, Inc.; 1430 Broadway;
New York, New York 10018
3) State and Local Regulations.
Proper Use of Tool
This sander is designed for sanding all types of materials i.e.
metals, wood, stone, plastics, etc. using abrasive designed for this
purpose. Do not use this sander for any other purpose than that
specified without consulting the manufacturer or the manufac-
turer's authorized supplier. Do not use back-up pads that have a
working speed less than 12,000 RPM free speed.
Work Stations
The tool is intended to be operated as a hand held tool. It is
always recommended that the tool be used when standing on a
solid floor. It can be in any position but before any such use, the
operator must be in a secure position having a firm grip and foot-
ing and be aware that the sander can develop a torque reaction.
See the section "Operating Instructions".
1) Read all instructions before using this tool. All operators must be fully trained in its use
and aware of these safety rules. All service and repair must be carried out by trained
personnel.
2) Make sure the tool is disconnected from the air supply. Select a suitable abrasive and
secure it to the back-up pad. Be careful and center the abrasive on the back-up pad.
3) Always wear required safety equipment when using this tool.
4) When sanding always place the tool on the work then
start the tool. Always remove the tool from the work
before stopping. This will prevent gouging of the work
due to excess speed of the abrasive.
5) Always remove the air supply to the sander before fitting,
adjusting or removing the abrasive or back-up pad.
6) Always adopt a firm footing and/or position and be aware
of torque reaction developed by the sander.
7) Use only correct spare parts.
8) Always ensure that the material to be sanded is firmly
fixed to prevent its movement.
9) Check hose and fittings regularly for wear. Do not carry
the tool by its hose; always be careful to prevent the tool
from being started when carrying the tool with the air
supply connected.
10) Dust can be highly combustible. Vacuum dust collection
bag should be cleaned or replaced daily. Cleaning or
replacing of bag also assures optimum performance.
11) Do not exceed maximum recommended air pressure.
Use safety equipment as recommended.
12) The tool is not electrically insulated. Do not use where
there is a possibility of coming into contact with live
electricity, gas pipes, water pipes, etc. Check the area
of operation before operation.
13) Take care to avoid entanglement with the moving
parts of the tool with clothing, ties, hair, cleaning rags, etc. If entangled, it will cause the
body to be pulled towards the work and moving parts of the machine and can be very
dangerous.
14) Keep hands clear of the spinning pad during use.
15) If the tool appears to malfunction, remove from use immediately and arrange for service
and repair.
16) Do not allow the tool to free speed without taking precautions to protect any persons or
objects from the loss of the abrasive or pad.
All manuals and user guides at all-guides.com
Operating Instructions
Putting the Tool into Service
Use a clean lubricated air supply that will give a measured air
pressure at the tool of 6.2 bar (90 psig) bar when the tool is run-
ning with the lever fully depressed. It is recommended to use an
approved 10 mm (3/8 in.) x 8 m (25 ft) maximum length airline. It
is recommended that the tool be connected to the air supply as
shown in Figure 1.
Do not connect the tool to the airline system without incorporating
an easy to reach and operate air shut off valve. The air supply
should be lubricated. It is strongly recommended that an air filter,
regulator and lubricator (FRL) be used as shown in Figure 1 as
this will supply clean, lubricated air at the correct pressure to
the tool. Details of such equipment can be obtained from your
supplier. If such equipment is not used then the tool should be
manually lubricated
To manually lubricate the tool, disconnect the airline and put 2 to
3 drops of suitable pneumatic motor lubricating oil such as Fuji
Kosan FK-20, Mobil ALMO 525 or Shell TORCULA® 32 into the
hose end (inlet) of the machine. Reconnect tool to the air supply
and run tool slowly for a few seconds to allow air to circulate the
oil. If the tool is used frequently, lubricate it on a daily basis or
lubricate it if the tool starts to slow or lose power.
It is recommended that the air pressure at the tool is 6.2 bar (90
psig) while the tool is running. The tool can run at lower pressures
but never higher than 6.2 bar (90 psig).
Drain Leg
Ball Valve
To Tool Station
Ball
Valve
Drain Valve
To Coupler
at or near Tool
2
Closed Loop Pipe System
Sloped in the direction of air flow
Filter
Regulator
Lubricator
Ball Valve
Air Hose
Air Compressor
and Tank
Air Flow
Air Dryer