Würth HKS 28-A Traduction Des Instructions De Service D'origine page 15

HKS 28 A.book Seite 15 Dienstag, 5. September 2017 2:51 14
Check lower guard for proper closing before
each use. Do not operate the saw if lower
guard does not move freely and close instant-
ly. Never clamp or tie the lower guard into the
open position. If saw is accidentally dropped,
lower guard may be bent. Raise the lower
guard with the retracting handle and make sure
it moves freely and does not touch the blade or
any other part, in all angles and depths of cut.
Check the operation of the lower guard
spring. If the guard and the spring are not op-
erating properly, they must be serviced before
use. Lower guard may operate sluggishly due
to damaged parts, gummy deposits, or a build-
up of debris.
Lower guard should be retracted manually
only for special cuts such as "plunge cuts" and
"compound cuts". Raise lower guard by re-
tracting handle and as soon as blade enters
the material, the lower guard must be re-
leased. For all other sawing, the lower guard
should operate automatically.
Always observe that the lower guard is cover-
ing the blade before placing saw down on
bench or floor. An unprotected, coasting blade
will cause the saw to walk backwards, cutting
whatever is in its path. Be aware of the time it
takes for the blade to stop after switch is re-
leased.
Do not work overhead with the saw. this man-
ner you do not have sufficient control over the
power tool.
Use appropriate detectors to determine if util-
ity lines are hidden in the work area or call the
local utility company for assistance. Contact
with electric lines can lead to fire and electric
shock. Damaging a gas line can lead to explo-
sion. Penetrating a water line causes property
damage or may cause an electric shock.
Do not operate the power tool stationary. It is
not designed for operation with a saw table.
Do not use high speed steel (HSS) saw blades.
Such saw blades can easily break.
Do not use grinding discs. Grinding discs are
not permitted for use with this power tool.
When working with the machine, always hold
it firmly with both hands and provide for a se-
cure stance. The power tool is guided more se-
cure with both hands.
Safety warnings for circular saws
Battery and Battery Charger
The enclosed operating instructions for the bat-
tery charger must be read carefully!
Secure the workpiece. workpiece clamped with
clamping devices or in a vice is held more se-
cure than by hand.
Always wait until the machine has come to a
complete stop before placing it down. The tool
insert can jam and lead to loss of control over
the power tool.
Avoid unintentional switching on. Ensure the
On/Off switch is in the off position before in-
serting battery pack. Carrying the power tool
with your finger on the On/Off switch or insert-
ing the battery pack into power tools that have
the switch on invites accidents.
Before each use, check the machine and battery.
If damage is detected, do not use the machine.
Have repairs performed only by a qualified tech-
nician. Never open the machine yourself.
Before any work on the power tool (e. g.
maintenance, changing the tool, etc.), remove
the battery. There is danger of injury from an
accidentally starting power tool.
Use power tools only with specifically desig-
nated battery packs. Use of any other battery
packs may create a risk of injury and fire.
Never allow children to use the machine.
Use only original Würth parts and accesso-
ries.
Under abusive conditions, liquid may be eject-
ed from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irri-
tation or burns.
Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of
fire when used with another battery pack.
Allow a heated battery to cool before charging.
Protect the battery from heat and
fire: Danger of explosion! Do not
place the battery on radiators or ex-
pose to strong sun rays for a longer
time; temperatures
cause damage.
Do not open the battery, and protect it from im-
pact. Store in a dry and frost-free place.
over 50 °C
15