BE Ag & Industrial BE-BRT Serie Manuel D'utilisation Et De Pièces page 15

SERVICING THE ROTOTILLER
The following information will help you make the necessary
checks and perform the procedures required to follow the
normal care recommendations made for your rototiller unit.
If you prefer, your local authorized dealer can make these
checks and perform the required procedures for you.
CHANGE FORWARD/REVERSE BELT
1. Turn off engine. Engine must be cool.
2. Remove spark plug wire and secure from spark plug.
3. Remove belt guard.
• Remove the forward belt from the forward engine pulley:
• Gently pull the engine recoil rope to rotate the pulley.
• With the pulley turning, force the forward belt out of the V-groove.
• Slide the belt free of the engine pulley.
• Pull the forward belt down and out of the way.
• Remove the reverse belt from the reverse engine pulley:
• Gently pull the engine recoil rope to rotate the pulley.
• With the pulley turning, force the reverse belt out of the
V-groove.
• Slide the belt free of engine pulleys and reverse belt guides.
• Pull belt down and away from transmission pulley.
• Install new reverse belt:
• Thread belt up from bottom.
• Tlace belt around transmission pulley in groove.
• Place belt under reverse belt guides.
• Gently pull engine recoil rope while forcing the belt over the
edge of the engine pulley into the V-groove.
CAUTION
Do not operate tiller before reading the engine manual provided in the parts packet
WARNING
Temperature of muffler and nearby areas may exceed 150° F, avoid these areas
IMPORTANT
Engine can overheat and become damaged if debris blocks the cooling system or rotating screen.
Never run engine without complete air cleaner installed on engine
• Install new forward belt:
• Place forward belt in transmission pulley groove.
• Gently pull the engine recoil rope to rotate the pulley while forcing the forward belt into the V-groove.
4. Replace belt guard.
5. Attach spark plug wire.
ENGINE MAINTENANCE
Refer to the engine manual included in your parts packet for information on engine maintenance. Your
engine manual provides detailed information and a maintenance schedule for performing the following tasks:
1. Check oil level before each use or after every 8 hours of operation.
2. Change oil after first 5-8 hours of operation. change oil while engine is warm. Refill with new oil of
recommended grade.
3. Check spark plug yearly or every 100 hours of operation.
4. Service air cleaner.
belt out of the V-groove.
- slide the belt free of the engine pulley.
The following information will help you
- pull the forward belt down and out of the
make the necessary checks and perform
way.
the procedures required to follow the
normal care recommendations made for
• remove the reverse belt from the reverse
your rototiller unit.
engine pulley:
If you prefer, your local authorized
- gently pull the engine recoil rope to rotate
dealer can make these checks and
the pulley.
perform the required procedures for you.
- with the pulley turning, force the reverse
CHANGE FORWARD/REVERSE
belt out of the V-groove.
BELT
- slide the belt free of engine pulleys and
1. Turn off engine. Engine must be cool.
reverse belt guides.
2. Remove spark plug wire and secure from spark plug.
- pull belt down and away from transmission pulley.
3. Remove belt guard.
• install new reverse belt:
• remove the forward belt from the forward engine pulley:
- thread belt up from bottom.
- gently pull the engine recoil rope to rotate the pulley.
- place belt around transmission pulley in
groove.
- with the pulley turning, force the forward
belt out of the V-groove.
- place belt under reverse belt guides.
- slide the belt free of the engine pulley.
- gently pull engine recoil rope while forcing
the belt over the edge of the engine pulley
- pull the forward belt down and out of the
into the V-groove.
way.
• install new forward belt:
• remove the reverse belt from the reverse
engine pulley:
- gently pull the engine recoil rope to rotate
the pulley.
- with the pulley turning, force the reverse
belt out of the V-groove.
- slide the belt free of engine pulleys and
reverse belt guides.
- pull belt down and away from transmission pulley.
• install new reverse belt:
- thread belt up from bottom.
- place belt around transmission pulley in
groove.
- place belt under reverse belt guides.
- gently pull engine recoil rope while forcing
the belt over the edge of the engine pulley
into the V-groove.
• install new forward belt:
BE-BRTXXX USER MANUAL
15