Publicité
Les langues disponibles
Les langues disponibles
en (original)
c.
Disconnect the plug from the power source and/or the battery pack from the power tool before
making any adjustments, changing accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d.
Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power
tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained
users.
e.
Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage
of parts and any other condition that may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly maintained power tools.
f.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g.
Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into
account the working conditions and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
h.
Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and
grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
5.
Service
a.
Have your power tool serviced by a qualified repair person using only identical replacement parts.
This will ensure that the safety of the power tool is maintained.
Only for AS/NZS: Mirka recommend that the tool shall be supplied via a residual current device having a rated residual
current of 30 mA or less.
Additional Safety Warnings
The safety of the tool is granted only by using original Mirka backing pads.
Read the Materials Safety Data Sheet (MSDS) for the work surface.
If any physical hand/wrist discomfort is experienced, stop working and seek medical attention. Hand, wrist and arm
injury may result from repetitive work, motion and overexposure to vibrations.
The power supply socket and connector are non-IEC appliance couplers. Only use an original Mirka power supply cable.
The Mirka power supply cable can be bought from your Mirka Dealer.
Check the tool, backing pad, power cord and fittings regularly for wear. If the power supply cable is damaged it must
be replaced by an original Mirka power supply cable.
Clean or replace the dust extractor´s collection bag daily. Dust can be highly combustible. Cleaning or replacing the
bag also assures optimum performance.
If the tool appears to malfunction, stop using it immediately and arrange for service and repair.
Always ensure that the work piece to be sanded is firmly fixed in place.
Keep hands clear of the spinning accessory during use.
Do not allow the tool to free speed without taking precautions to protect surrounding people and objects in the event
that the abrasive or backing pad should come loose.
Technical data
DEROS II
Power
Mains voltage
Speed
Orbit
Size of backing pad
Weight
Degree of protection
Noise and vibration information
The measured values may be used for comparing one tool with another and in a preliminary assessment of exposure.
58
Mirka® DEROS II 325, 350, 550, 625, 650, 680 & 750
325
350
300 W
300 W
220 240 VAC
220 240 VAC
4,000 10,000
4,000 10,000
rpm
rpm
2.5 mm (3/32")
5 mm (3/16")
Ø 77 mm (3")
Ø 77 mm (3")
0.8 kg (1.8 lbs)
0.8 kg (1.8 lbs)
I
I
550
625
400 W
400 W
220 240 VAC
220 240 VAC
4,000 10,000
4,000 10,000
rpm
rpm
5 mm (3/16")
2.5 mm (3/32")
Ø 125 mm (5")
Ø 150 mm (6")
1 kg (2.2 lbs)
1 kg (2.2 lbs)
I
I
650
680
400 W
400 W
220 240 VAC
220 240 VAC
4,000 10,000
4,000 10,000
rpm
rpm
5 mm (3/16")
8 mm (5/16")
Ø 150 mm (6")
Ø 150 mm (6")
1.1 kg (2.4 lbs)
1.1 kg (2.4 lbs)
I
I
750
400 W
220 240 VAC
6,000 9,000 rpm
5 mm (3/16")
Ø 175 mm (7")
1.1 kg (2.4 lbs)
I
Publicité
