EINHELL TC-SP 204/2 Instructions D'origine page 22

•
When you have finished your work, switch off
the machine. Do this by pressing the red "0"
button. Then disconnect the machine from the
mains supply.
•
Move the planing knife cover (12) back into
the lowest position and cover the planing kni-
ves over their entire length.
•
Always keep the push stick (3) ready to hand
in the holder provided. (see Fig. 11).
7.2 Thicknessing
Warning! Pull out the power plug before perfor-
ming any maintenance, cleaning and adjusting
work.
7.2.1 Adjustment (Fig. 13)
Place the hand crank (4) on the post on the
planing table (14) and turn it to adjust the thick-
nessing table (20) to the required height. The set
angle can be read off the scale (29).
7.2.2 Fitting the chip extractor
(Figure 11-15)
•
Undo the locking knob (32) and pull the pla-
ning knife cover (12) forwards as far as possi-
ble.
•
Place the chip extractor (5) on the planing
table (14). Ensure that the stop pins and the
securing screw (34) are in the appropriate
holes and are engaged in the internal threads
on the planing table (14) and that the recess
(b) is on the safety switch (e).
•
Turn the securing screw (34) until the chip
extractor (5) is secure.
•
Attach the extraction system adapter Ø 100
mm (27) to the connection for a sawdust ext-
ractor (5).
•
Connect the plane to a chip extraction system
(not supplied).
7.2.3 Thicknessing mode (Fig. 11/14)
•
Connect the mains plug to the mains lead.
Press the green "I" button to start the planer.
•
Place a workpiece on the thicknessing table
(20). Guide the workpiece towards the feed
table (13).
•
When you have finished work, switch off the
machine. Do this by pressing the red "0" but-
ton. Then disconnect the machine from the
mains supply.
•
Use the pull-out workpiece support for long
workpieces (10).
Anl_TC_SP_204_2_SPK13.indb 22 Anl_TC_SP_204_2_SPK13.indb 22
GB
7.3 Changing the knives (Figure 16)
•
Warning! Always pull the mains plug before
changing the knives.
•
Set the feed table to the maximum planing
depth. (see 7.1.1)
•
Remove the parallel stop following the inst-
ructions in 6.3 in reverse.
•
Pull the planing knife cover (12) forwards as
far as possible so that the entire knife block
(23) is exposed.
•
Undo the clamp screws (c) by turning them
clockwise using the open-ended spanner
(17) supplied. Turn the knife block (23) so that
the latch (22) can be pulled out with the knife
(21).
•
Clean all the relevant parts and the knife slots
in the knife block (23).
•
Fit the latch (22) with the new knife (21) and
align them with the side of the knife block.
•
Place the blade adjustment block (15), as
shown in Figure 18, on the knife block. Make
sure that the knife (21) touches both sides
of the blade adjustment block (15). Make
sure that the knife reaches the same working
height as the planing table.
•
Tighten the clamp screws (c) using the open-
ended spanner (17) supplied.
•
Return the planing knife cover (12) to its origi-
nal position so that the knife (21) is covered.
Warning!
Only use knives which are recommended by the
manufacturer for this equipment. If you use other
knives there is a risk of injuries due to lack of
control. Avoid over-tightening and the possibility
of the thread becoming detached. If the latch (22)
or the screws have worn out threads they must be
immediately replaced.
8. Troubleshooting
1. The machine cannot be switched on:
•
No mains power. Check the power supply.
•
Carbon brushes worn. Have the carbon bru-
shes replaced by an electrician.
•
Safety switches (d/e) not activated.
2. The machine cuts out when idling:
•
Power failure (check fuses). Have the fuse
replaced by an electrician.
- 22 -
15.02.2024 08:50:58 15.02.2024 08:50:58