Publicité
RECORDING
4. Set the Dolby NR system by pressing the DOLBY NR
button.
@
For CT-43, CT-S820S and CT-S620:
Press the DOLBY NR ON/OFF button to turn the Dolby NR
system ON first, then select the Dolby NR system.
. Press the DOLBY HX PRO button to turn the Dolby HX
PRO system on and off. (CT-95 and CT-S920S only)
. Prepare the audio source from which you wish to re-
cord. Turn on the stereo amplifier and prepare it for
playback of the desired audio source.
. If you
use
SUPER
AUTO
BLE
turning,
press
the
SUPER AUTO BLE START/CLEAR
button.
©
Wait approximately 10 seconds until "TUNE" is displayed in
the counter indicator and the BLE DATA indicator lights (see
page 29). (CT-43, CT-S820S, CT-S620 only)
e
Wait
until the
counter
indicator
returns
to the
normal
counter, and the BLE DATA
indicator lights. (CT-95, CT-
$9205 only)
@
The bias is adjusted automatically, but when desired, you
may perform the adjustment manually by using the BIAS
(—/+) buttons after the AUTO
BLE tuning has been com-
pleted.
@
The tape will be forwarded after pressing the start button so
that recording will start from the recordable portion of the
tape. The operation is completed when the start position is
resumed.
To stop AUTO BLE tuning
To cancel AUTO BLE tuning (e.g. must record urgently), press
the stop (M) button.
_To reset a tuned condition
Press the SUPER AUTO BLE START/CLEAR button again.
Error display
If the old tape, the tape end or the leader (white portion) im-
mediately prior to the tape end is reached during AUTO BLE
operation, tuning becomes impossible. That means recording
will stop immediately and the counter indicator will display the
following (flashing) message: "Err".
In this case, press the SUPER AUTO BLE START/CLEAR button
again to reset, and record without AUTO BLE tuning. |
8. Press the recording (e) button.
@ The unit is set to recording standby mode, called one-touch
recording pause.
@
The [REC] indicator and pause (#§) indicator light up, and
monitor is set to source with the [SOURCE] indicator lit.
24
<RRE1078>
En/Fr
ENREGISTREMENT
6. Préparer la source audio à partir de laquelle enregis-
trer. Mettre l'amplificateur stéréo sous tension et le
préparer pour la lecture de la source audio désirée.
. Si l'accord SUPER AUTO BLE est utilisé, appuyer sur
la touche SUPER AUTO
BLE START/CLEAR.
© Attendre approximativement
10 secondes jusqu'à ce que
"TUNE" soit affiché dans l'indicateur du compteur et que
l'indicateur BLE DATA s'allume (voir page 29). (CT-43, CT-
$8208, CT-S620 seulement).
e
Attendre jusqu'à ce que l'indicateur du compteur revienne
au compteur normal et que l'indicateur BLE DATA s'allume.
(CT-95, CT-S920S seulement).
@
La polarisation
est ajustée automatiquement,
mais
le ré-
glage peut être effectué manuellement, si désiré, en utili-
sant les touches BIAS (—/+) après que l'accord AUTO BLE
est terminé.
@
La bande est avancée après avoir appuyé sur la touche de
départ de sorte que l'enregistrement commence à partir de
la partie enregistrable de la bande. L'opération est terminée
lorsque la position de départ est déterminée.
Pour arrêter l'accord AUTO BLE
Pour annuler l'accord AUTO BLE (par exemple en cas d'enre-
gistrement urgent), appuyer sur la touche d'arrêt (W).
Pour réinitialiser un état accordé
Appuyer de nouveau sur la touche SUPER AUTO BLE START/
CLEAR.
Affichage d'erreur
Si la bande est vieille, que la fin de la bande ou que l'amorce
(partie blanche) immédiatement avant la fin de la bande est at-
teinte pendant l'opération AUTO BLE, l'accord devient impossi-
ble. Cela signifie que l'enregistrement s'arrêtera immédiate-
ment et que l'indicateur du compteur affichera le message sui-
vant (clignotant): "Err".
Dans ce cas, appuyer de nouveau sur la touche SUPER AUTO
BLE START/CLEAR
pour réinitialiser et enregistrer sans l'ac-
cord AUTO BLE.
8. Appuyer sur la touche d'enregistrement (@).
@
L'appareil est réglé dans le mode
d'attente d'enregistre-
ment, appelé "pause d'enregistrement par touche unique".
@
L'indicateur [REC] et l'indicateur de pause (If) s'allument
et le contrôle
est réglé sur la source
avec
l'indicateur
[SOURCE] allumé.
Publicité
